Vintage car handle hardware...

I am trying desperately these days to be a bit more “creative” and get out of my “everything white” funk.

I saw a really cute idea on Pinterest….vintage car handles as hardware. Naturally I jumped on Ebay and began searching for vintage car handles. I looked back at my Ebay history…I ordered them in JANUARY!!! Didn’t have anything in the works, just thought is was a cute idea.

Did I save the link to the “inspiration?” Um, no. Did I have a plan in mind as to how to attach them to a drawer front.? Um, no. Did I have a table to even attach them to? Um, no.

Just thought it was a super cute idea.

The first thing I had to do was figure out how to attach the handles to a drawer front…the hole in the backside is not threaded. My original plan was to find a bolt that fit snuggly in the handle hole, then just use JBWeld…love that stuff. The problem with that is it would make it darn near impossible to remove the handles in the future. Not MY problem, but as I have said before, I want buyers to be able to makeover the piece again in the future.

Thought maybe I could JB Weld a light fixture bolt (threaded on both ends) into the handle, then just add a nut and washer…hum….that could work and still allow for removal in the future.

While I was at Lowes scouting bolts one of the nice associates showed me this nifty brass insert thingy….

Because brass is “soft” you can screw this little plug into the hole (using a flat screwdriver), then get a bolt that will fit the inside of the plug…in this case a 5/16 hex bolt. I slipped a washer onto the bolt so that it would sit snuggly against the back of the drawer.

Problem 1 solved.

Problem 2 is finding the perfect little table…fortunately I found a cute little solid wood side table at a garage sale for a few bucks….

Problem 3….as you may have noticed, the handles have a 1” “bump” on the backside which would make it impossible for them to sit flush on the drawer front.

I removed the little wood handles on the drawer fronts and puttied the little holes.

I took a 1 3/8” paddle bit (I couldn’t find my 1 1/4”) and made a hole in the front of the drawer front deep enough for the handle to sit flush. Then I used a 5/16” drill bit to make a hole in the center of that hole for the bolt.

TIP: To make sure you don’t drill your large hole all the way through the drawer front, wrap a piece of blue/masking tape on the paddle bit to indicate the depth you need to drill. (Not pictured)

Now I was able to set the car door handle flush on the front of the drawer and run the bolt (with washer) through the backside and into the little brass plug.

Since I knew the bolt may “loosen” and there is only one bolt holding the hardware in place, I added a dab of construction mastic (liquid nail will do) to the hole just to give the handle some stability.

Before applying the hardware, I primed, sanded, tacked and painted the table a high gloss red (See HERE why I can no longer call it my KSTP process.) The insides of the drawers were a tad cruddy so I primed those as well and painted them black…not necessary but kinda cute!

I found some “L” shaped metal floor trim and decided to add it to the front corners of the little table….installed the new door handle hardware….and presto bingo….

Too stinking cute!!!!

And now that I have figured out all the logistics to turning vintage car handles into hardware, grab a few and have some fun!!!

I have a few of these door handles left…now I just need to find another little table or small dresser!!!!

Info

Comment

More painted furniture projects and how you can get perfect paint results!

I know I share a lot of painted furniture projects. There was a time when I was a "paint snob." If it is wood, no paint.

But I have learned in my resell business that paint is often the best way to "enhance" a piece and give it new life.

We all have "that piece." The one mom gave us or maybe we bought at a thrift store or garage sale because we needed a dresser or side table. A maple dresser from the 60s or one of those fake wood "cherry" tables from the 80s. We still need it for the storage or even to fill a space and buying new just isn't an option.

As I have said before, life is too short to live with ugly furniture and even the ugliest piece can benefit from a little "makeover"

Updating an old dresser or bedside table isn't difficult. Yes, Pinterest is filled with precious stenciled and glazed projects...and we all envy. But simple is easy and the impact can be huge. I have shared hundreds over the years and every week I complete at least 2-3 pieces that often do not get shared...either I forget to take pictures or they sell so fast I think "why bother."

So today, again, I'm going to share a few simple little projects and how to get the best results.

Mini makeovers that can make a huge impact in any room!

This campaign dresser had seen it's better days....

As you can see, it had been seriously abused. But even the ugliest piece has potential....

Not the best "after" picture, but I didn't think to take a picture before I took it into 410 Vintage so I snapped one with my phone...but you get the idea. (If you haven't been to 410, GO!)

It sold the day I took it in! These "upcycled" dressers are perfect for a bedroom or even a tv and storage cabinet in the living room.

You might have noticed one piece of the hardware was missing. I happened to have one of the pulls from this project so I used the same method to retrofit it. You don't have to do anything that complicated...most home improvement stores have tons of hardware options. All the hardware was solid brass so I cleaned it up with some Brasso, steel wool and elbow grease. The point...the hardware doesn't have to be all matchy-matchy.

This little bedside table had seen it's better days!

A simple little makeover...paint and new hardware....new life....

This is a typical hard rock maple dresser you can find for next to nothing at thrift stores and garage sales...

Usually sturdy as the day they were built, but seriously ugly and dated!

They obviously can benefit from a little love and attention...nothing fancy just a little paint and hardware update....

An inexpensive little "fake wood" side table......

And AGAIN...

I liked the brass hardware on this one so I just cleaned it up!

Sooooo...what do all these projects have in common.

KSTP...Kilz (or any good primer!), sand with 220 grit paper, wipe down with a tack cloth and paint.

The two dressers were painted with latex paint using a 4" foam roller and paint brush. I used spray paint on the two little side tables.

So, here are a few TIPS for getting the best results when painting furniture.

1) Always clean the piece of any dirt or debris. Just wipe it down with a damp cloth and make sure you get all the "ick" off! If the piece is super grungy, you might want to clean it with ammonia or wipe it down with mineral spirits! (If it has a lot of flaking paint, you can sand it down a bit or better yet, strip it using this process...just make sure the existing paint or finish is stable!)

2) Make repairs. DO NOT waste your time making it pretty if it needs repairs. And remember, glue and clamps are your friend!!!! If you don't know how to repair something, google it or email me. MOST furniture repairs aren't that difficult...but if you do it wrong (or not at all) you will be wasting your time making it pretty!

3) Primer....always a must if you are going to paint with spray paint or latex or oil paint. I swear by the oil-based Kilz. If you want your paint to stick and not chip or peel, prime. For smaller projects I use spray Kilz. For larger projects I roll on Kilz with a 4" foam roller. Even if your paint says "all in one paint and primer"...use primer.

4) Sand smooth after the primer has thoroughly dried. A 220 grit paper should do the trick...FEEL the surface...if you can feel it, the paint won't hide it.

5) Use tack cloth. Most tutorials will tell you to wipe the piece with a damp cloth. That won't cut it! Tack cloth will pick up the finest grains of dust and debris you can't see until you paint the piece! Use it!

6) If you are going to brush on latex or oil, use a quality brush AND TAKE CARE OF IT! I have brushes I have owned for years because I am religious about cleaning them thoroughly after use. And don't even think about using those cheap disposable brushes (chip brushes). They are great for many things, but not for getting a smooth paint finish on furniture!!!!

7) ALWAYS use an additive....Floetrol for latex, Penetrol for oil based paints.

8) Use quality paint. Especially spray paint. I know it is cheaper at discount stores but pay the extra few dollars and buy a quality spray paint at your home improvement store. Cheaper will NOT be better if it doesn't hold up to wear and tear! I do 2-3 light coats (spray or brush) rather than trying to get solid coverage with one coat...trust me when I say, there is NO paint on earth that will get good coverage with just one coat!

9) Cure time is important. Seriously, I know they style their pieces on those HGTV shows within hours of painting a piece of furniture. Just don't! Just because the paint feels dry to the touch DOES NOT mean it has cured. Latex...a few days...oil...a week. Give your paint time to cure or it is going to peel or chip if you try to use it right away! Put the piece in place and chill!

10) Spray vs. Brush/roller. For me, it all depends. I have learned that large flat areas are tough to get an even coat of paint on with spray paint...and of course there is the expense factor for large pieces. A dresser can take 2-3 cans of spray paint. So it really depends of the piece. Sometimes I will spray the drawer fronts of a dresser and roll the top and sides.

11) Keep a little spare paint for chips and dings...if you use latex or oil, just put a few tablespoons in a little container and stick it in the back of the drawer...just in case! If you are using spray paint, keep a can with a little paint. Manufacturer's change paint colors and you might not be able to find that awesome color in the future. Keep spare paint in the house...not the garage or storage shed!

Regardless of whether you spray or roll/brush, you have to follow the first rules of KSTP....Kilz (primer), sand smooth, then tack....then paint!

If you follow these simple guidelines, you can update a dated piece with just a little time and effort.

Again, life is too short to live with ugly furniture...

Info

Comment

"New" barstools and a few dresser makeovers!

Last week I shared the prep work on the "chest of drawers from hell."

This week I was able to get it painted and the hardware installed! Precious!

I kept the paint treatment fairly neutral with one of my favorite off-whites...."Swiss Coffee." The white and teal combo has been selling VERY quickly, but I decided to stay simple and neutral with this one! Partially because I absolutely adore this hardware and I didn't want to do anything to distract from it!!

As I mentioned last week, I painted the interior of the drawers to seal in the "funk" and make them look a little better! I used some leftover paint I had from another project...takes a few extra minutes but honestly, well worth the time and effort!

As you can see, the extra time I took to repair the damaged veneer on the top and the side really paid off!

I took this little chest to 410 Vintage...it lasted all of about 4 hours! Confirmation that all the hard work was well worth it!

I did paint one old dresser I had with the teal and white combo...

Just one of those old maple dressers...a little paint, a little gel stain on top, some new hardware and this baby sold within two hours of taking it in! (I didn't even bother to take a photo before I delivered it...this is one I snapped with my phone!)

I also finished up another little project waiting in the wings...these old bar stools!

Certainly not something you would want in your kitchen which might explain why I was able to pick them up for a few bucks each at an auction. Pretty ratty!

But with a little KSTP treatment and a simple reupholstery job on the cushions, beautiful!

After I disassembled them, I cleaned them up, sprayed them with Kilz, sanded smooth, wiped with a tack cloth, and then I sprayed them with a satin white spray paint. I had some leftover grey herringbone material from Sister's tufted chair project (will share that soon!) so I used that to recover the seats.

Recovering barstool seats and dining room chair seats are one of the simplest "reupholstery" jobs a DIY newbie can tackle. And it can completely change the look of a stool or chair. Again, TONS of great tutorials online for this simple project!

Again (and again and again) if you have a "ratty" piece of furniture that just doesn't trip your trigger any more, CHANGE IT! Life is too short to live with ugly furniture!

YOU CAN DO IT!

Info

Comment

Simple makeovers for the worst offenders...the KSTP treatment!

There is NO excuse for ugly furniture. With warmer weather just around the corner, it is time to start looking at your furniture with a critical eye and making a list of pieces that CAN be changed with just a little bit of work!

We all have it...those "cheapo" pieces of furniture that are, at the very least, offensive! Maybe they were given to you, maybe you bought them at a "discount" store...maybe you bought it at the thrift store to fill space in a room.

Pressed board construction, laminate tops, dated finishes, pieces you put together with a little allen wrench thingy that came with the worthless little "screws" that promptly strip out and leave the piece wobbly and worthless!

It's ugly and cheap, but seriously who has the money to buy "real wood" furniture when you are struggling from pay check to pay check and having to buy shoes for a kid whose feet seem to grow a size every month.

I get it...I've been there. Fortunately I have learned to shop resale and auctions for "quality" pieces...and even if they need a little TLC, I have the tools, knowledge and time. But not everyone has that...or the money to buy and refinish high quality pieces.

That is why I advocate the KSTP treatment. Let me explain....

First, before you even get to the KSTP treatment, ALWAYS give the piece a good cleaning. On the nastiest, I use ammonia water but some can just be wiped down with a little water and mild detergent. Whatever you need to do to get the gunk off the piece! If it is "stuck" on just scrape it off with a razor! No matter if you scratch the finish...you are going to paint it!

Second, make any and all repairs that need to be made...and if you don't know how to repair it properly, google it!

Okay, now the KSTP treatment....

K- Kilz (my favorite primer but any QUALITY PRIMER will do! That is why this is the KSTP treatment and not the PSTP treatment!)

For smaller pieces I use a spray can only because it is easy and gives me a nice smooth finish. On larger pieces I use a brush and 4" foam roller! TIP! Always shake the can longer than the directions recommend. Kilz will spray on with a "grainy texture" if you don't shake the can well! No biggy since you are going to sand anyway, but just makes it a little easier! Also, pay attention to the temperature recommendations...it matters!

Many paints SAY they are a "primer and paint in one." Sorry, I am old school....I ALWAYS prime and I personally recommend it. If you want a superior finish that will hold up to use and abuse, prime!

S-Sand. A 220 grit paper will usually smooth out the piece after it is primed. I wrap a piece around a sanding sponge block!

If you have "ornate" legs or detailing, use 000-0000 steel wool.

USE YOUR HANDS, not your eyes. Feel the piece.

Trust me, if it isn't smooth, it WILL show after you paint it! Sand it until it is smooth to the touch! If you cleaned the piece well, scraped off all the gunk, this step really should only take a few minutes.

T- Tack cloth. A MUST after you sand but before you paint (or apply any finish). Blow or brush off as much as you can, then use a tack cloth!

You can purchase it at your favorite home improvement store...usually in packages of 2 and relatively inexpensive (around $2)! You can wipe a piece down all day with a clean cloth, but you WILL leave "stuff" on the piece if you don't tack cloth it. Tack cloth will remove EVERYTHING. If you still feel "stuff," hit it with the sand paper again and then tack cloth again!

P-Paint. This is where people usually freak out. My favorite for wood or laminate furniture is oil-based but it can be a tricky paint to work with for a novice and difficult to clean up. Fortunately latex paints have come a long way and are much more durable these days! QUALITY spray paint is probably your best bet for smaller pieces. I say quality because you can buy spray paint a tad cheaper at discount stores, but I am not a huge fan of cheap paint for ANY project! I usually buy Valspar or Rust-oleum from Lowe's.

On smaller pieces of furniture the difference will only be a few dollars but will be worth it in the long run.

Each of the brands come in LOTS of great colors...just find the color you love! I have found very little difference between the two brands...the Valspar tends to dry a tad quicker....but both are quality paints! ALWAYS shake the cans well and follow the directions on the can!!!

I have followed every tip in the book to get rid of the occasional "striping" on large, flat surfaces...like dresser tops or table tops. It doesn't seem to matter how I spray, what the temperature is or how hard the wind is blowing...sometimes I get stripes.

My solution has been to purchase the little "sample pots" of paint custom mixed to match the spray paint I am using and roll it on the large flat surfaces with a 4" foam roller!

Penetrol and Floetrol are a MUST any time you roll or brush on paint...oil or latex!

Use it. It will eliminate the brush and roller marks and give you a MUCH smoother finish!

These are just a VERY few projects using the KSTP treatment (I have done hundreds!)....world of difference for a little bit of work! I am working on a piece right now that is in the S stage...primed and sanded but now I need to figure out what color I want to paint it...soon!

Even light fixtures and paddle fans can be spray painted!!! On metal pieces and furniture hardware, I use metal primer primarily for the "rust retardant" factor!

One last important TIP when using ANY technique to paint anything....ALWAYS give the piece time to cure before you put it to work!

I was always skeptical of those "two day" makeovers they did on tv where they would paint something and then "stage" the pieces with all kinds of stuff within hours of putting a final coat on. (Kind of like getting your nails painted at the salon...even though you dry them for 10 minutes, you are still going to ding them if you dig in your purse for your keys! Unless you get gel polish...awesome stuff!) Trust me, that is the fasted way to ruin a finish! Don't do it...be patient and give the paint time to harden (cure) before you set a lamp on it or try to hang the fixture (trust me...I have had to repaint many pieces because of impatience!)

One dated, nasty, cheapo piece of furniture can ruin an entire room. Toss it or paint it! YOU CAN DO IT!

*I have not been compensated for pimping these products! These are the products I use and work for me!!!*

Info

Comment

Updating a little chandelier...

I am almost embarrassed to admit where I got this ugly little brass chandelier....

Out of the back of a strangers pick up truck at the dump. Seriously...I was paying out at the local dump and this guy drove up in a truck loaded with trash. Sitting on top was this light fixture. So I asked him if I could have it...and he said SURE!

Geez...I have become one of "those" people who dig through other people's trash! Crazy cat lady, annoying coupon lady...and now this...(shaking head in disgust)

Whatever...I wasn't sure what exactly I was going to do with it but I knew it could be "updated" if I could just find the right inspiration. I knew I was going to paint the dated brass, so I decided to start there until I could figure out exactly what I wanted to do with the fixture!

Originally I primed it with metal primer, then started painting it with plain ole' off white spray paint. (Remember, when you aren't sure what to do with something, take it to "base neutral.")

And that is when a little DIY project turned into a total disaster. Yes, it happens. Even to me. Even though I shook the spray paint can per the instructions, it still started spraying all "clumpy." I don't know how to describe it, but rather than a nice smooth finish, it was all grainy and rough....AAAAGGGGGHHHHH!

Made me so mad I tossed the fixture in the back of the garage and said "SCREW IT." (Yes, I curse at innate objects!) I knew I was going to have to completely sand it down and considering the "ornateness" of it, I knew it would be a royal pain. My "vision" was just a heap of "mess."

Then I saw this on Pinterest...

Andrea at "Personally Andrea" took a plain ole' chandelier and dolled it up a bit by using jute twine to wrap the ugly little plastic tubes.

Hum....just the "inspiration" I needed to dig the "ruined" chandelier out of the back of the garage and give it another shot!

I sanded down the "grainy" finish, reprimed where needed and then painted it in my current favorite teal spray paint! (This time I shook the crud out of the can AND test sprayed it!)

Covering the ugly plastic tubes is super easy. Andrea used tape, but I used hot glue. I ran a little line of hot glue along the tube as I wrapped it in the jute twine.

WORD OF WARNING!!! Hot glue is HOT...and the plastic sleeves are a tad flimsy so use the glue sparingly or you will actually melt the little tube which will make it impossible to slip back onto the light. (Lesson learned the hard way...fortunately Lowe's sells replacement socket covers for under $3 a pair!)

I think painting the fixture in black or oil-rubbed bronze would have made it a little more "formal." But I was going for "fun" and "hip" and a little more casual!

I liked the look so well I decided to do the same to my dining room fixture using the plastic covers I purchased at Lowes!

I found some glittery gold fabric/paper kinda looking stuff at the craft store that I am going to use to cover new socket covers for the Christmas holiday! I will share that later when I do my Christmas decorating!

Don't turn your nose up at the dated brass fixtures...as I have shared many times fixtures, lamps and fans are super simple to update with a little paint.

And of course a little inspiration! Thanks Andrea!

Info

4 Comments

"Blah" to "BAM" cheap furniture makeovers...YOU CAN DO IT!!!

This past week I have been working on my kitchen (I told you the "small" projects wouldn't squash the urge!) I still have a few little trim details to hunt down and then I will try to do a feature next week. I had to construct three different types of open shelving and I rewired an 80 year old Westinghouse fan...AND IT WORKS!!! I'll share all that as well!

This week I want to share a few little projects that YOU can do! Do you have a piece of furniture (or two or ten) that is just "blah?" A cheap little shelving unit you picked up at the big box store and put together with the little allen wrench that came with the screws. Maybe a few ancient bedside tables you inherited from your mom. A particle board table that has seen it's better days.

I know I have harped on this before, but seriously it bares repeating! If you are just starting out, are on a tight budget, feel the need to keep furniture given to you by family, or just want to change things up a bit, you NEED to be able to do simple makeovers!

Before you toss a piece of furniture to the curb, think about "updating" it a tad. Even the cheapest, most basic piece can be saved with just a tiny bit of time and effort! As I have said time and again, the worst that can happen is you still hate it and it still only brings $1 at your next garage sale.

I find pieces like this all the time at my apartments. I drag them home, clean them up with ammonia (stinky but gets the old gunk off!) and then give them a little facelift!

This was one haul out of one unit....

The little bedside tables are the old orange maple...ugly as sin but super sturdy and solid wood! The little coffee table is one of those inexpensive "fake" wood things that comes with the little allen wrench tool for the bolts! And the spindle shelf had particle board shelving. All in all, pretty dated stuff!

This little shelf came out of another unit...

It was missing a drawer and it had a few loose bolts, but whatever...still salvageable!

I find these things in my apartments, but you can find them at thrift stores and garage sales for next to nothing!

All I did to the little shelf with reeded drawers was give it a little KSTP treatment (Kilz, sand, tack cloth and paint!

Perfect for added storage in a bathroom, kitchen or kid's room!

I decided to do something a little fancier on the coffee table and bedside tables. I striped the tops with the acetone/lacquer thinner mixture, added a little java gel stain, then sealed them with spray on poly (if stripping and staining is beyond your skill level, just paint the tops!)

The bases are simple KSTP treatment. New hardware on the bedside tables and these pieces are perfect for updating any space!

The spindle corner shelf got a simple KSTP treatment!

I don't have a "before" picture of the little chalkboard shelf. Basically it was a stained wood frame with an ugly picture of a teddy bear! Ewwwww. Gave the frame a chalkpaint and distress treatment (spray paint would work too!) and I painted the board backing with chalkboard paint. Super simple "upcycle!"

Years ago I scrapbooked all the boys athletic pictures. A chore considering they both played football and baseball their entire childhood! (I strongly suggest you do this every year rather than try to find time to do all 15 years at once!)

The square frames were a perfect fit for a 12x12 piece of scrapbook paper and would be perfect for someone who wanted an easy way to display their kid's sports pictures. I applied the scrapbook paper onto the foam backing with a spritz of spray adhesive, used a glue stick to attach pictures and KSTP the frames. This would be the perfect way to "scrapbook" photos...then you can take them out of the frame and just slip them into an album when it is time to change out the pictures next year!

Before you paint a piece, make sure all the "bolts and joints" are tight and the piece is sturdy. If tightening a screw or bolt doesn't solve the wobbles, take time to GLUE AND CLAMP whatever ails the piece. No sense in making it pretty if it is going to collapse the first time one of the kids leans on it!

All these projects have one thing in common. Spray paint. Seriously...a little primer, a little sanding and a little spray paint...and you have changed the entire look!

I have shared many of these simple little makeovers in the past! A few dressers here, here here and here. Several coffee tables here, here and here and Lord knows how many frame makeovers (here, here, and here!)

Challenge yourself. Pick out ONE piece of furniture or a frame in your house you really don't like. Go to Lowes and pick up a can of Kilz, a little sandpaper, a package of tack cloth and a can of your favorite color spray paint (total under $15) and give it a go! YOU CAN DO IT!

I promise!

Info

5 Comments

Little oak side table....

I am so bummed. I really wanted to share my little laundry room door project I mentioned last week. The only thing holding me up is the glass. I called and the glass came in, but it was wrong. DANG IT!!!

So today I am just going to share a simple little table.

One of the reasons I needed a flea market space was because I was always finding cool little pieces at my apartments. I would haul home a table or dresser or chair and give it a cute little make over...and then give it away!

I don't mind giving things away to friends and family...but after awhile I did have to come to terms with the fact that I was spending money (not to mention a lot of time) on these little makeovers...so the "rehab to resell" became a necessity. That, and I tend to haul home A LOT of little goodies from auctions and as I have said before, if I didn't have the flea market outlet (and wasn't a tad OCD) I could easily become a hoarder.

I love auctions...and I love restoring furniture. What can I say!

Anywho, I found this little solid oak table in an apartment. It was super sturdy and had already been stripped so it really just needed a little TLC.

I did scrub the top with my acetone/lacquer thinner mixture just to clean it up a bit. Then I stained the top with a walnut stain and applied 3 coats of tung oil finish. After that cured well, I taped and papered off the top and gave the bottom a KSTP treatment. (For those who are new, that is Kilz/sand/tack cloth/paint. I used my current favorite Valspar teal color.

New life for an old, abandoned table destined for the dumpster. Now it is a perfect little side table for the living room or even a bedside table.

Looking back at all the projects I have shared, it is easy to see that I still struggle with painting EVERYTHING....seems I almost always try to preserve a little "natural wood" if I can. Personally, I think the paint "updates" the piece and the stained wood gives it warmth. I am working on a desk and a fireplace surround right now and both have stained tops and painted bases....guess that's just my thang!

Hopefully the RIGHT glass will come in this week and I can share my door next week! I can't wait...it's going to be awesome!!!

In the meantime, pull your least favorite piece of furniture into the garage or yard and give it a little KSTP treatment...trust me...you're gonna love it!

Info

2 Comments

June 2015...and MORE chairs!

June 2015 will go down as an eventual month for me.

For the first time in 34 years, I have no minor children. Katie turned 18 this week and it is official...ALL my children are old enough to vote, be drafted and be sentenced to an adult correctional facility.

We finally had to put our wonderful lab, Ginger, to sleep. She was 13. It was time but that didn't make it any easier. This is the second precious pet we have lost this year. Heart breaking.

And for the first time in years I really felt the sting of Father's Day. My dad has been gone for 20 years but this year was, for some reason, tougher than normal. He died exactly one week before Father's Day so this time of the year is always kind of a "double whammy."

Then there is the accidental "new member" of the family....and may explain some weird typos in my posts.

I keep a trailer at my apartments for abandoned furniture. A mama cat set up household in the furniture with her 4 babies. A few weeks ago, we THOUGHT we made sure all the kitties were off the trailer before we took it to the dump....only to find two of them still on the trailer when we got there. I managed to grab one and throw it in the truck, but the other ran under the truck. We spent 30 minutes crawling around on the nasty red clay/garbage ground trying to get that stupid kitten, only to have it bolt. Gone. I was heart broken. But to make matters worse, I could not find the other kitten ANYWHERE in my truck. Both Matt and Katie helped me darn near dismantle the interior of the truck...it was not there. I left the windows down the entire day and even put out some food just in case.

THREE VERY HOT DAYS LATER I went to the truck in the evening...and there was that silly kitten sitting on the back of the seat. It had been in a hot truck, with no food or water, for THREE DAYS! I couldn't believe it survived and neither could the vet.

Soooooo....we have a new "miracle kitty." And being the softy that I am, I can't bring myself to take it to the shelter. Especially with all the guilt I feel for losing her sibling and in spite of my puffy, itchy eyes.

Yes, she is a she. About 8 weeks, according to the vet, but if that is the case, she is a tiny kitty.

Cleo thinks it is hers and tries desperately to carry it around in her mouth...which means the poor kitten is constantly soaked in dog slobber. It is pathetic, but she tolerates it for some reason. And typing on the computer is like a game to her...hence the typos. She's a funny kitty!

We haven't named her yet...I keep hoping someone will want her and take her so I will quit itching and sneezing. Why bother...if the three other cats haven't killed me by now, this little half pint won't either! I like Mimi...Katie does not. Mitchell suggested Kitty, but we have a Ms. Kitty because she was another "rescue" that was only suppose to be here until I had time to take her to the shelter...around 9 years ago. So he suggested Little Kitty...so maybe "Litty."

ANYWHO!!!!! When I am having "emotional turmoil" my tolerance for some things is darn near nil. So when I went up to my booth last week, I was annoyed by a few things that have been sitting in there for MONTHS...specifically two chairs. So I threw them in the back of the truck, brought them home and gave them a quick makeover!

The first is a little folding chair I chalk painted eons ago...I had two and sold one, but this one has hung around far too long. I gave it a little KSTP (Kilz/sand/tack/paint) treatment with white spray paint...then I covered the seat with some leftover fabric from this chair makeover!

The other is a walnut mid-century chair. It is really difficult for me to paint over walnut...but the chair has been in my booth for months as is, and if I am going to sell it, I have to give it a little "pow treatment." Again, a KSTP treatment and new upholstery...someone is going to love it!

I know I make these little chair makeovers sound easy. And usually they are! Chairs are one of the easiest pieces of furniture to "update"...especially ones that just need a little paint and fabric on the seat.

But OCCASIONALLY I bring home a real kicker. One I KNOW is going to take a LOT of time and attention! This chair is a prime example!

I know...it is a HOT MESS!!! I have NO doubt that several people at the auction where thinking "What the heck?" (Including Brian...but again, I think he now trusts my judgment!) But I was so excited I couldn't stand it!

I was pretty sure, from a quick inspection on a broken piece (that was there, thank God!), that it was most likely mahogany. At this point, after just a tiny bit of research, I THINK it is a Victorian Eastlake arm chair. But I honestly don't know because so far I haven't found anything just like it...only similar. Castors on the front legs and not on the back and hand carvings and stamps on the wood.

And of course the BILLIONS of little nails that were used for the upholstery! ALL of which had to be removed!

I knew the finish was masking some beautiful wood so I couldn't wait to start stripping it! In this picture you can see where I applied the stripper (used in this tutorial) on the left....

Here is the "before" and "after" of the side...

The intricate carvings require some real work, but as I have said before, the very best tool for stripping old finish out of carvings and corners is a good ole' toothbrush! I still have a lot of stripping and scrubbing to do but after two afternoons, I have all 100,398,365,003 nails out and a tiny bit of the frame stripped!

The fabric is in such bad shape, I honestly don't know what it is...and I wonder if it didn't originally have another fabric on it since there are SOOO many nail holes. Many of the Victorian chairs I have seen have a velvet fabric....what to do, what to do!

My point...not all chairs are easy...some require a little more time and attention. I am going to take my time with this one and there is a good chance I won't sell it. At least not until the next little treasure comes along!

Info

11 Comments

Another mid-century dresser makeover...

If you have followed along for any amount of time, you know I have a "thing" for mid-century furniture...and walnut.

I just love the clean lines of the pieces and how sturdy they are. You can not buy furniture today that is as durable and sturdy as many of these 50-60 year old pieces. Well, I guess you can, but you will pay a pretty penny for them!

And walnut? Well, in my opinion, there isn't a more beautiful wood grain out there.

A few months ago I featured a beautiful mid-century dresser I refinished and put in "Mitchell's room." I knew it was a tad big for the room, but I just could not resist.

As strange luck would have it, I was cruising Craigslist and found the matching chest. It just so happens that the people who owned the flea market where I originally purchased the dresser were selling the matching chest. Wow. What are the odds!

I actually ended up paying a tad more for the chest than I did the dresser...and it was in a little rougher shape structurally.

One of the big "boo-boos" on this piece was some pretty substantial chipping on the veneer of the top drawer corners....

Several of the drawers had missing or broken bottom "glides" and one had been VERY poorly repaired! (Hence, THIS rant!) And one of the legs was a little whomper-jomped. (Technical term for loose and wobbly)

I can not stress enough how important it is to make proper repairs. People, wood glue and clamps are your friend! I could do a tutorial a day on properly repairing furniture, but truth be told, there are a billion outstanding tutorials online for every imaginable repair. No, DO NOT use nails to secure dislocated dove joints. No, do not use silicone to try to put a drawer back together. No, do not put sheetrock screws in the leg of a dresser that originally had a bolt and clamp. If you don't know how to properly fix it, GOOGLE IT! (or email me...I love telling people what to do!) Seriously, it isn't hard to repair furniture, but if you do it wrong, I promise it won't last...and all the paint and refinishing you did to make the piece "pretty" will be a waste of time!

So, the first thing I had to do was repair and rebuild a few drawer glides. Then I had to fix the leg which required removing the old bolt, filling the hole with wood and glue and then replacing the bolt. Then I had to figure out what to do with the chipped drawer fronts.

Since I had refinished the drawers on the dresser, I really wanted to refinish this piece to match. Since there is really no good way to "rebuild" veneer and then stain it to match, I decided to remove the damage by creating a little "radius" on the corners. Probably not the best thing to do on a style known for it's clean, straight lines. I contemplated just cutting the corners at a 45 degree angle...but naaaaaa.

My goal was to improve the aesthetics a tad and also prevent further damage to the veneer in the future.

I used a paint can to draw a "radius" on the corner....

...then I used my mouse sander with 220 grit paper to carefully sand away the damage and round the corners. This is what I call "sculpting" a piece and it takes time and patience. When sanding, always start with a very smooth grade of sand paper (220-330) and only use a rougher grit if it is absolutely necessary. And ALWAYS sand with the grain!

Other than the chipping, the veneer was in pretty go shape and still intact. If I had used a rougher grit, I risked chipping or damaging the veneer further.

When it was all said and done, it turned out pretty well.

After making all the repairs, I stripped the top, drawers and legs using 1/2 acetone and 1/2 lacquer thinner and steel wool. I knew I wanted to paint the "cabinet" like I did the dresser, so I taped and papered off everything that was going to be left "natural" and sprayed it will Kilz, sanded smooth, wiped it down with a tack cloth, and sprayed it with my favorite spray paint.

The top, drawer fronts and legs were left natural. I didn't apply a stain because I love the look and color of walnut with nothing but clear oil.

I used the same process I use on all stained or natural wood. First I hit it with 0000 steel wool (always WITH the grain) just to smooth it a bit. Then I applied 3-4 coats of Formby's tung oil finish, rubbing it with 0000 steel wool and a tack cloth between each coat.

In all honestly, I really do not need two large dressers in this room. It is just the "guest room" now. But I really can't part with either of these pieces! They are just too beautiful!

Don't turn your nose up at old pieces that need a little time and attention. In the end, if you do it right, they will be well worth it!

Info

8 Comments

Display hutch...before and after!

Brian has long since stopped questioning my purchases at auctions. I think he has developed a little bit of faith in my ability to make something out of nothing. But occasionally I do question myself. I must have subconscious flashes of inspiration that, in the stark light of day, are forgotten because occasionally I will look at a piece I brought home and think "WHAT WAS I THINKING!!!"

This would be one of those pieces....

It's not a horrible piece...it's just very "ho-hum." Not an antique or even remotely interesting. Just...well...boring.... for lack of a better word.

Basically just a "pine and particle board" piece that is pretty dated...seriously, hunter green?

The upside to this piece is it did not need any major repairs...just a few nuts and bolts tightened here and there. The stained top, shelves and crown where in good shape and didn't need to be refinished.

Honestly, it just needed a little "facelift." A brighter color to update it a bit! I taped and papered off the stained areas, removed the ugly wooden knobs and gave it a little KSTP treatment (Kilz, sand, tack cloth and paint!)

My favorite teal spray paint and simple little black knobs and we are good to go!!!

I even "displayed" a few of my auction finds just so the pictures would have a tiny bit more interest! This piece would be an awesome addition to a kid's room, an office, or even in a kitchen!

Again, this is one of those "boring" or "dated" pieces you probably have floating around your house. Whether it be bedroom furniture, a little table, an old dresser, or even a dated light fixture, a couple of hours and a few cans of spray paint can make all the difference. You don't have to be even remotely creative...just find your inspiration and go for it!!!

I have a garage full of projects I have been working on since the weather warmed a bit! I can't wait to share...something for everyone!