Mid century chest makeover....

On rare occasions I find a little treasure hidden among all the garbage my tenants leave when they move in the middle of the night! I found this little table years ago and it started my love affair with Lane Acclaim tables....

It did NOT look like this! I remember I picked up the nasty little thing and started to toss it in the back of my truck. But it was sturdy and I could see quality through all the "muck" so I brought it home. I googled the markings on the underside and found that it is a walnut and oak Lane Acclaim table manufactured in 1959. With a lot of elbow grease and a little tung oil, it is now one of my favorite little "treasures." Along with the others I have purchased and restored over the years. Still waiting on the desk and a round end table...but someday...

Now I look at furniture I find a little closer.

This dresser is one of my recent finds. A true mid century piece. Completely intact and sturdy as the day it was built. Unfortunately someone had done a REALLY bad job painting it!

I cleaned it, primed it with Kilz, sanded it and wiped it down with tack cloth....then I painted it with one of my favorite flat "charcoal" greys. The ole' KSTP treatment! The drawers were in mint condition and just needed a little cleaning!

Beautiful! Because of the style, I kept the finish simple. While I hesitate to paint MCM pieces, this is a prime example of "enhancing" a piece.

Now I am going to share a little DIY frustration because I know I make this stuff LOOK easy sometimes. I first painted this entire piece with several cans of Valspar flat spray paint. I like spray paint because I normally get a nice smooth finish. For some reason I kept getting that "stripped" look on the top and sides...the drawers looked fine. Not a problem I normally have with flat finishes when the temperature is decent. I ended up buying a quart of latex flat paint, mixed to match, (and added floetrol...a must!) and used a 4" sponge roller to get a uniform finish. Worth the extra effort!

I know I have said it a thousand times....don't overlook those "ratty old" pieces.....neglected or abused or poorly "restored." With a little bit of your time and attention, they can be beautifully restored and ready for another lifetime of use!

This week I will be sharing this project at...

...love their features and their site!

Info

1 Comment

A few simple chair makeovers!

I usually have several chairs piled in my garage waiting on a makeover. The reason they get "piled" is because most require, at the very least, a smidge of sewing. My LEAST favorite thing to do! (Okay, root canals are pretty bad, but at least they give you drugs!) I usually wait until I have 2-3 projects that need sewing before I drag out the sewing table and get it all done at once!

Right now I still have two of the mid century dining chairs waiting to be refinished...no sewing needed, but they are small and tend to get pushed aside...time and again.

And honestly, I had intended to refinish these and keep them but that plan didn't work out so I refinished and sold two of them!

I have a mid century lounge chair I desperately want to refinish and reupholstery, but I bought it to keep so I have no doubt the selection of an appropriate upholstery will take months!

I did manage to get two chairs finished over the last few weeks.

The first is a simple little maple chair I picked up at Salvation Army.

A "tired and tattered" little thing to say the least.

I decided to go simple...a little chalk paint and distress on the frame (followed by a coat of poly to seal it) and drop cloth for the seat. This is the first time I have used gimp for trim, but it turned out nice. I just hot glued it over the gathered skirt.

I didn't even bother to make a back cushion...I like the look of the wood slats!

This cain chair was a tad more complex. Naturally I completely forgot to take a "before" picture until I had already started deconstructing it! But I have no doubt you have run across them in thrift stores and garage sales...a dime a dozen and pretty much what they are worth in their current state! The real gem is finding one with all the caning in tact!

I really was at a loss as to what to do with this chair...until my daughter suggested I do it in blue and gold! Actually, she suggested teal, but I found this blue and white material I really loved! She was right about the gold...it is all the "rage" right now and becoming very popular!

After removing the seat and all the upholstery, I primed the entire chair with Kilz, sanded and wiped it down with tack cloth. Then I sprayed it with white spray paint! After that had cured well, I taped off the legs and sprayed them with metallic gold spray paint. I wasn't sure whether I wanted to keep the tufting on the back but I sprayed the buttons and reused them. They didn't really turn out "gold" like I had hoped...more a "brownish" color, but honestly, close enough. I used metallic gold bias tape to make the piping and the double welting (Here is a tutorial on making piping out of bias tape!) A simple little process, but again, it does require hauling out the sewing machine (ick!)

Again, I could provide a step by step tutorial on "reupholstering" these simple little chairs, but there are dozens of tutorials on line (including video tutorials) that are ten times better than anything I can do. And every chair is different, so find a tutorial that makes sense to you AND has a chair similar to what you have! This is the very first chair I ever tackled. Knowing what I know now, I can do better. I can honestly say that I learn something new every time I tackle a project like this and regardless of the little imperfections here and there, they always end up WAY better than what I started with!

I tend to be a tad on the OCD side when it comes to projects...but I have learned that nothing is ever going to be perfect! And again, as my very wise Daddy use to say "You'll never notice it on a passing train!"

Which reminds me...Happy Father's Day Daddy! It has been twenty years (this month), but some days it seems like we just talked yesterday. I wish you were here to see all the things I have learned to do. All because you taught me that working with my hands (and my head) and making something out of nothing really can be rewarding! I know you would be proud! Thank you.... and I miss you!

Happy Father's Day to all the great men out there who are blessed with kiddos!!! Be the man you want your son to be and be the man you want your daughter to marry ;)

Info

2 Comments

Another mid-century dresser makeover...

If you have followed along for any amount of time, you know I have a "thing" for mid-century furniture...and walnut.

I just love the clean lines of the pieces and how sturdy they are. You can not buy furniture today that is as durable and sturdy as many of these 50-60 year old pieces. Well, I guess you can, but you will pay a pretty penny for them!

And walnut? Well, in my opinion, there isn't a more beautiful wood grain out there.

A few months ago I featured a beautiful mid-century dresser I refinished and put in "Mitchell's room." I knew it was a tad big for the room, but I just could not resist.

As strange luck would have it, I was cruising Craigslist and found the matching chest. It just so happens that the people who owned the flea market where I originally purchased the dresser were selling the matching chest. Wow. What are the odds!

I actually ended up paying a tad more for the chest than I did the dresser...and it was in a little rougher shape structurally.

One of the big "boo-boos" on this piece was some pretty substantial chipping on the veneer of the top drawer corners....

Several of the drawers had missing or broken bottom "glides" and one had been VERY poorly repaired! (Hence, THIS rant!) And one of the legs was a little whomper-jomped. (Technical term for loose and wobbly)

I can not stress enough how important it is to make proper repairs. People, wood glue and clamps are your friend! I could do a tutorial a day on properly repairing furniture, but truth be told, there are a billion outstanding tutorials online for every imaginable repair. No, DO NOT use nails to secure dislocated dove joints. No, do not use silicone to try to put a drawer back together. No, do not put sheetrock screws in the leg of a dresser that originally had a bolt and clamp. If you don't know how to properly fix it, GOOGLE IT! (or email me...I love telling people what to do!) Seriously, it isn't hard to repair furniture, but if you do it wrong, I promise it won't last...and all the paint and refinishing you did to make the piece "pretty" will be a waste of time!

So, the first thing I had to do was repair and rebuild a few drawer glides. Then I had to fix the leg which required removing the old bolt, filling the hole with wood and glue and then replacing the bolt. Then I had to figure out what to do with the chipped drawer fronts.

Since I had refinished the drawers on the dresser, I really wanted to refinish this piece to match. Since there is really no good way to "rebuild" veneer and then stain it to match, I decided to remove the damage by creating a little "radius" on the corners. Probably not the best thing to do on a style known for it's clean, straight lines. I contemplated just cutting the corners at a 45 degree angle...but naaaaaa.

My goal was to improve the aesthetics a tad and also prevent further damage to the veneer in the future.

I used a paint can to draw a "radius" on the corner....

...then I used my mouse sander with 220 grit paper to carefully sand away the damage and round the corners. This is what I call "sculpting" a piece and it takes time and patience. When sanding, always start with a very smooth grade of sand paper (220-330) and only use a rougher grit if it is absolutely necessary. And ALWAYS sand with the grain!

Other than the chipping, the veneer was in pretty go shape and still intact. If I had used a rougher grit, I risked chipping or damaging the veneer further.

When it was all said and done, it turned out pretty well.

After making all the repairs, I stripped the top, drawers and legs using 1/2 acetone and 1/2 lacquer thinner and steel wool. I knew I wanted to paint the "cabinet" like I did the dresser, so I taped and papered off everything that was going to be left "natural" and sprayed it will Kilz, sanded smooth, wiped it down with a tack cloth, and sprayed it with my favorite spray paint.

The top, drawer fronts and legs were left natural. I didn't apply a stain because I love the look and color of walnut with nothing but clear oil.

I used the same process I use on all stained or natural wood. First I hit it with 0000 steel wool (always WITH the grain) just to smooth it a bit. Then I applied 3-4 coats of Formby's tung oil finish, rubbing it with 0000 steel wool and a tack cloth between each coat.

In all honestly, I really do not need two large dressers in this room. It is just the "guest room" now. But I really can't part with either of these pieces! They are just too beautiful!

Don't turn your nose up at old pieces that need a little time and attention. In the end, if you do it right, they will be well worth it!

Info

8 Comments

Walnut MCM dresser makeover...Part 2!

You can see "Part 1" of this makeover here...a tutorial on stripping and oiling these amazing pieces!

Okay, I have to admit...EVERY time I work on one of these walnut pieces, two things happen...I fall madly in love with it and I am reminded of how much I LOVE walnut!

This little table is a prime example!

Solid walnut and an absolute true treasure! It certainly didn't LOOK like a treasure when I brought it home, but with a little time and effort, these pieces can become breathtaking additions to any home decor.

I know painted furniture is ALL the rage right now and I agree whole-heartedly that there is indeed a time and a place for painted furniture. My decorating motto...if you can ENHANCE the piece by painting it, go for it!

Some people aren't real keen on stained furniture...and that is okay. But I believe every decor needs the warmth and beauty of a quality natural wood piece...whether it is a table or chair or whatever! Not every piece needs to be painted and no decor should have ONLY painted furniture. Of course, no decor should have ONLY stained furniture either...even I throw in painted pieces here and there...probably not enough for some people's taste, but I do like to "lighten and brighten" occasionally. I painted my bedroom furniture and my office desk and even the little side table in my den. But you may note one common element on all these pieces...I left a little bit of natural wood! (Wow, looking at these old posts I realize my photography skills have come a long way! Still a ways to go, but definitely better!)

I decided to go with both paint and natural wood finish on this dresser. I like the way the painted "box" seems to frame the wood drawers! In my opinion, the results are A.M.A.Z.I.N.G!

So get ready for a BUNCH of pictures...because I am loving this piece!!!!

As I mention in the first post, the top had some pretty serious ink stains...

With a little "chemical" magic, gone!! When you find yourself faced with wood stains, hit the internet and search for a chemical solution. Trust me, sanding is NOT the answer, especially if you are working with veneer.

Can you even believe that this.....

...could become this. No stain...just a simple strip job and 4 coats of tung oil finish! Walnut in all it's natural glory!

I put this dresser in my oldest son's room. He doesn't actually LIVE here, but he still has a lot of stuff here. His room serves as a guest room and a place to keep all his "stuff." The other kids call it the "museum"...trophies, jerseys, plaques, certificates..high school and college mementos covering pretty much every square inch of the wall space.

Sooooo...it was time. Time for a fresh coat of paint. Time to box up most of the "stuff." Just time.

So later this week I will share his room makeover.

Want to know a little secret? For the first time ever I didn't stress over paint chips trying to pick the perfect paint color. I chose a color that everyone has been raving about on Pinterest and decor blogs. I literally called the paint store and told them to mix up 2 gallons, sight unseen...and I LOVE it!

I can't wait to share!

I am sharing this project with Christine at MustLoveHome.com as well as all my favorite Link Parties!

You can see the full room makeover here!

Info

10 Comments

Mid century chair SCORE!! And a Duncan Phyfe chair repair!

SCORE! Seriously, major score!

Okay, so they don't look so hot right now and they didn't look any better piled on a trailer at the auction, covered in gunk and spider ick!

Which is a good thing because nobody knew what they were...which means SCORE for ME! Baumritter mid-century dining chairs! Oh my!

I know they look rough right now, but let me work my magic on them!

Truth is, mid-century furniture hasn't really hit the big time here like it has in other parts of the country and honestly, we don't see a lot of it around here. But occasionally I can find pieces here and there.

I love them...everything about them. The grain and color of the wood after it is refinished (usually walnut or teak), the clean lines, the incredible construction! I love the entire process of restoring these pieces because I know they will take my breath away when I am finished. I also know it is next to impossible to find solid walnut and teak furniture these days.

So...what is my hard-fast rule? If I bring one in, I have to take one out. So sacrifices have to be made and the sacrifice is going to be the rest of my antique Duncan Phyfe chairs! I have already sold 2 and have four left...two painted side chairs and two caption's chairs.

Last year I featured the chair I had to repair. I was so proud of myself. I glued and sculpted the chair back that was broken and then painted the two side chairs, which kind of goes against my grain but they turned out beautiful. I didn't paint the caption's chairs....

The repair lasted all of about 6 months...and then the back busted again. CRAAAAAP!

So this time I decided to "rebuild" rather than repair.

This would have been SOOOO much easier had I just gone and bought a scroll saw. But oh no...I figured I could do this with my jig saw and Dremel. And I did...but next time I am going to buy a scroll saw!

First thing I had to do was deconstruct the chair to get to the "broken back." Fortunately, these chairs are constructed with dowel rods and the top pops right off...okay, you have to beat on it a bit and chip the paint...but it eventually comes off.

Then I had to find a little piece of wood the same thickness as the back...3/8". I figured that wouldn't be a big deal. It was. I ended up finding some 3/8" pine, but it wasn't wide enough...so I had to do the ole' clamp and glue thing to create a piece wide enough.

This is no big deal...truth is, most large wood slabs, and even smaller ones, are nothing but smaller pieces of wood glued and clamped together...most table tops are constructed that way!

After I let the piece sit for a day or so, (I was busy priming, sanding and painting my bedroom furniture...can't wait to finish and share!) I used wood filler to fill any gaps in the joints, sanded the piece smooth and traced the broken piece onto the wood...

....then I cut it out with a skill saw and dremel.

This is not a job for the faint of heart, impatient people or someone who has had more than 1 cup of coffee. You have to go slow and use a light, steady hand. I actually cut on the outside of my mark and then used sand paper to sand down to the mark.

This process would have gone a bit quicker had the wood not split a time or two. It never split at the glued joints, just on the grain, which meant I had to glue and clamp the split and wait! Grrrr.....

Anywho, after hand sanding and sculpting for a few hours, I had a piece that was pretty darn close to the original! Then it was just a matter of priming, sanding and painting it.

I reconstructed the chair and hit the entire back with another light coat of paint and sealer.

Presto...ALMOST good as new! Can you tell which is which?

I can...the chair on the left is the repair. The big difference is the "lines" that are missing from the middle...after all the cutting and sculpting and sanding, I wasn't going to risk messing it up by trying to chisel lines in the wood.

And I will be honest...fitting it all back together was NOT as easy as it sounds...there was some additional sanding and grinding and even a few curse words! But in the end it turned out pretty good!

Also, I noticed the paint has "yellowed" over time. That is pretty common for "whites." Something to keep in mind when contemplating "touch ups." There is a good chance you will have to paint the entire project if the color has faded, yellowed or changed over time!

Now that it is repaired and I feel good that it will hold up, I plan on selling this chair and the matching one and the two caption chairs so I will have room for my mid century chairs when I get them refinished.

If I bring one in, I have to take one out!!!

Hopefully I will get that done before Thanksgiving...or we may all be sitting on lawn chairs!

Info

Comment

Drexel Declaration Mid Century coffee table...

I know I am always talking about how AWESOME some of my furniture finds are, but this is truly an AWESOME piece!!! Mid century and walnut...my absolute favorites! (Check out some of my other mid century finds and makeovers here!)

We scored this coffee table at an auction. I probably should have flipped it over and looked for markings before bidding, but it is pretty big and honestly, I didn't want to draw too much attention to it (gotta be "cool" at the auctions!) When I bid on it, I knew nothing about it other than it was walnut and mid century! Structurally, it was in mint condition and I knew it could be spectacular with a little elbow grease. The scratches and water sports were not too bad! We were told it had been stored in an old outbuilding for years....I believe it!

The piece is marked on the bottom. It is a Drexel Declaration coffee table. A relatively "rare" piece with a good value!

As I have said before, it is not the "profit value" that motivates me. It is the absolute LOVE I have for this furniture.

It has been in my garage for months. I just didn't have the time or space to mess with it! The first thing I had to do was strip it. Keep in mind the finish on these pieces are 50+ years old so the old varnish has "yellowed" over time. And of course there is all the wear and tear...scratches, water damage, worn finish! But you CAN NOT strip old paint or varnish inside. The chemicals are just too strong and stripping and sanding does make a bit of a mess so I made sure I got all stripping and sanding done before it got too cold to work outside! (I really need a heated shop!)

I almost always use Formby's furniture refinisher to strip old varnish. I find that it really does a great job of "melting" the old finish off while hydrating the wood. Occasionally I may have to use something a little stronger and on very rare occasions I will actually sand the piece. I did take some sand paper to this piece only because there were several "water stains" that just couldn't be chemically removed.

I can not stress enough how important it is to CAREFULLY sand old furniture! Veneers can be very thin and it is easy to get carried away! Always start with a fine grain paper (220 grit) and work your way to a heavier grit ONLY if you need it. Then work your way back to a fine grit!

You may not be able to remove every stain or imperfection. And that is okay! Old and antique pieces are going to have imperfections! Embrace them! My office desk I featured here is a prime example....

Try as I might, I could not get this old cigarette burn to go away...and that's okay. It is a constant reminder of one of the many reasons I shouldn't start smoking again!

Fortunately I was able to get almost all the "imperfections" off the coffee table.

Also, most finishes were originally applied in a way to make the wood grain appear "uniform." A multi-layer technique may have been used or the finish and stain were sprayed on. Once the original finish is removed, you are likely to find that the wood grain no longer has a "uniform" appearance. Again, embrace it!

After making sure I removed ALL the old finish, I "washed" the entire piece with mineral spirits. This is an important step when refinishing furniture whether you are applying a clear finish or painting. It removes all the gunk and oils. Then I hit is with a very fine sandpaper just to knock down the grain a bit.

The mineral spirit wash will also give you an idea of what color the wood will be when you apply a clear finish. Most woods will be a completely different color stripped than it will after a clear finish has been applied. After you wash the piece with mineral spirits, the wood will eventually dry back to a natural color, but while it is wet you will be able to tell what color it will be after a clear finish is applied and whether you will want to apply a darker or different color stain. I personally love the color of natural walnut after a clear finish is applied, so rarely will I apply a stain.

After wiping the piece down with mineral spirits, I wiped the entire piece down with tack cloth to remove dirt and dust. Again, you can wipe down a piece all day with the cleanest cloth...I can promise you the tack cloth will find more! Use it and use it between EVERY coat of finish or paint!

After stripping, sanding and tacking, I began applying the Formby's tung oil. I love this stuff...in my opinion it is a superior finish to poly! Super easy to apply and much less room for error. If it gets scratches in the future, just hit it with 0000 steel wool, tack cloth and then apply another coat of tung oil. Simple!

Because of the weather, I had to apply the tung oil inside. The smell and fumes from tung oil is not that bad. Steel wool itself tends to crumble and create "dust" so I decided to try something new...which is NOT something I do easily! I picked up these little "finishing pads." They seem to work pretty well! I still favor the steel wool, but the pads produced far less "dust" than the steel wool!

A little trick when painting or refinishing...place aluminum foil under the feet/base after you are finished sanding and tacking. Most paint and finish won't stick to aluminum foil (unlike paper) and it will protect your floor and keep dust from being dragged onto the base when applying the finish!

I usually apply 3-5 coats of tung oil. I use a "stain sponge." You can usually find them in the stain section at Lowe's. Three coats is usually enough, but if I still feel the finish is "uneven" I will continue to apply coats until I get an even "gloss" look. ALWAYS rub it down with 0000 steel wool and tack cloth between each coat.

Whether you use steel wool or finishing pads or sand paper, make sure you always sand WITH the grain.

"Sanding" and tack cloth between each coat is VERY important. I used tack cloth before I applied the first coat of tung oil and I could still see and feel "crumbs" after it dried!!!

I love this piece. I think it looks a tad too big for my living room, but I just can't bring myself to part with it! Honestly, I think I would like it a bit better if I had a bigger rug. This one has always been a tad too small, but it was cheap and I just needed something to throw down to keep our toes warm! With an old kitty in the house, you don't invest too much in rugs.

So I have been looking...Joss and Main...Overstock...I'm looking! Someday.

(UPDATE! Yep, that is the NEW rug...featured it here...and I seriously love it! I am so honored to be featured on betterafter.net! Gail asked to see the inside, so here is a picture with the top open. As you can see it has a little compartment with a sliding drawer. The inside was in mint condition, so I did not do anything to it!)

and Better After!

and Curbly.com

Info

56 Comments

The Birdies on a light fixture or lamp shade!

I received several positive comments about the little bird pillows featured here! They really are darling. I took the pillows I featured to my booth and then made two more for my den.

I also painted the bird silhouettes on my laundry room wall...featured here. ( I would like to add...this laundry room reveal has been "pinned" and featured a BUNCH!!! Awesome!)

When I spotted this little light fixture on clearance at Lowe's, I just knew it would be perfect for the bird silhouettes! Simple metal base and a linen shade. The metal was "antique bronze"... not my favorite but an easy fix! (Kind of makes me wish I hadn't already set my heart on the fixture I already installed in the laundry room! )

I painted the base black. Since it is metal I first sprayed it with the auto primer and then two coats of gloss black.

If you can't easily remove the shade, make sure you tape it off REAL well!

Then the tricky part....painting the birds on the shade.

This post gives you a step by step tutorial on painting on fabric. As I mentioned, if you screw up or get this paint on the fabric, it is NOT coming off. Painting on a round shade is NOT easy. So get comfy and take your time. I basically used the same exact process I used to paint on the fabric for the pillows!

Somehow, by the grace of God, I managed to paint the silhouettes without messing it up!

I painted a silhouette on each side of the shade. When I hung it in my booth, you can see the birds from both sides...AWESOME!!

Dressing up a basic fixture or updating light fixtures is NOT hard. Often it costs way less than going out and buying new fixtures. Here I featured exterior lights I purchased at a garage sale for $5.00...new glass, a little elbow grease and a little paint...as good, or better, than new!!

Don't stop at light fixtures...updating old lamps and paddle fans can give new life to out-dated or boring fixtures! Check out how easy a little "make-over" can be here!

And if you don't know how to take down an old fixture or install a new one, just check out my tutorial here. It is not hard and YOU CAN DO IT!!!!

Info

8 Comments

FINALLY, a chair before and after!!!

I say FINALLY because as I have mentioned I have "upholstery block." I can pick paint, I can pick stain...but I have the toughest time picking out upholstery. Which is becoming a real problem because I have all these chairs in my garage that need upholstery work!

Anywho, I finally picked an upholstery for these little mid century style slipper chairs....

I was a little hesitant to go with something so "funky." But fact is, I don't think these chairs have a tremendous "value" so it was a perfect opportunity to do something fun with a style I love! When I found a "'50's Paris" themed fabric at Hobby Lobby, I decided to go for it. Who wouldn't love the Eifel Tower, 50's fashion and PINK???!!!

The legs were oak...sturdy but not my favorite, so I didn't have a problem painting them....a little primer and black satin spray paint. I added a little batting but otherwise they were in pretty good shape! And really comfy! The chair didn't originally have any piping, but I added a little black around the base of the seat.

I found a black and white diamond pattern fabric I am going to make little pillows out of of...eventually. I stuck my houndstooth pillow on there just to see how it would look...not so great, but I think the diamond pattern will look awesome!

Personally, I think they are pretty cute...we'll see if they sell...

Info

2 Comments

Mid century side tables...

I have been working hard to find pieces I know others will just love! Problem is every once in a while I find pieces I absolutely fall in love with and I know I will have a hard time letting go! Especially after working on them all day!

I believe these tables are black oak. The tops, sides and drawers were veneer, but the bases were solid. Really beautiful tables with great "bones."

I primed and painted the boxes. Then I stripped and stained the drawers and bases and coated them with 4 coats of tung oil.

Honestly, it will be tough letting go of these two.

But someone, somewhere will love them....hopefully as much as I do!

FOLLOW BECKWITH'S TREASURES ON FACEBOOK! Now if I can just figure out how to put one of those little Facebook widgets on this blog!

Info

1 Comment

Wicker chair fit for a little ballerina...

It is so hard to take a picture of a piece of furniture that was white but is now a PALE mist green...but I tried!

It may not appear in the picture to be a huge difference, but it really is! And it is perfect for a little girl's room! Now if I only had a "little" girl....

What is truly amazing about the color I painted the little chair (Valspar, Mellow Spring) is it matches the color of my 60+ year old Universal Ballerina Mist stoneware to a T!

My paternal grandmother wasn't a "china" kind of lady...so this was really all she had. My mom bought the gravy bowl and plate, the serving platter and the tea pitcher at the estate auction after Grandma passed....while she was carrying it back to her car she dropped the pitcher!! So when mom gave me what she had, the pitcher was beyond repair. So I did what I always do...I Googled the pattern!

Turns out it isn't a real expensive stoneware pattern...but the color and style is really beautiful and very "mid-century" since it was probably made and acquired in the 50s. It is a "mist green" with a platinum band...just awesome. So when I found more pieces out there, I bought another tea pitcher, the milk pitcher, salt and pepper shakers, a serving bowl and the sugar and creamer set.

Being the "family historian" and "archive fanatic" that I am, I carefully wrapped the broken pitcher, put it in a box, and wrote the story of why there was a broken tea pitcher in it and how I acquired a replacement.... with a Sharpie...on the box! Hopefully my family won't think their mom was crazy for keeping a broken tea pitcher in the attic (trust me, they have enough reasons!)

This week while I was sniffing around a new antique shop in town, I found another set of salt and pepper shakers!