A few MCM makeovers and a life decision...

Again, I am a baaaad blogger. I jump head-long into a project and fail to take “before” pictures.

Prime example…

No “before” picture. It was in similar condition to THIS dresser…reeeeally bad. But of course I have no proof of that. Just take my word for it…again.

The entire piece was originally the old “natural” finish with a lot of “wear and tear.” I primed and painted the six side drawers and cabinet and stripped and oiled the top and middle drawers.

I absolutely love the wood handle “hardware” and the super nifty black concave and brass hardware. I sprayed the little concave pieces with metal primer and black paint.

The top had some chipped veneer. I originally planned to paint the top so I could repair these areas, but I just can’t resist beautiful walnut…even veneer. So I did what I often do…I just let it be what it is…an older piece with a few blemishes. You can buy replacement strips of veneer…but I would rather have flawed original…just a personal preference!

I did take a before picture of this piece….

I love the brass hardware on these pieces…again, the way to tell if it is solid brass is to use a magnet. A magnet will not stick to solid brass. Important because in order to clean these pieces I have to really scrub them with steel wool. No secret to cleaning brass hardware…lots of Brasso, steel wool and elbow grease!

Now…on to my “life decision.”

I have decided to stop doing the whole “auction/flea booth/resale” thing. I love doing what I do but doing it to “pay the rent” has become tiresome. I am just not enjoying it the way I use to.

So this past week I gave my notice at 410 Vintage and I went on a major “purgefest” in my garage (aka shop). I sold a lot of stuff on Facebook Marketplace, I donated a truck load to our local community thrift store and I took a truck load to the dumpster.

I have a friend who opened an awesome little consignment/flea market (Gathered Goods) so I took a few things to her to sell on consignment.

My garage has been a disaster for some time.

I painted the walls and cleaned all the shelving and cabinets!

I installed a Rubbermaid track system for large items….

…and we installed a nifty metal peg board system for all our tools. I knew where all my tools were but no one else could really figure out where anything was.

I even gave the door between the garage and laundry room a fresh coat of paint.

I am not “retiring” completely. I will still refinish and rehab pieces…I just won’t have to go looking for projects. If I find a project I want to work on, I can always take it to Darlene at Gathered Goods.

So fear not…I will always have a project to share here…and of course there are always my enlightened “muse” posts.

Info

Comment

A whole lot of shaking going on!

AGAIN, I have been MIA for weeks. Trust me, I would have loved to have a day to sit and muse.

As I shared here, Matt moved into a new home and Katie moved out of her college apartment.

I laugh at people who think their “parenting” somehow ends when their kid turns 18. Trust me, that is when the REAL work begins. In my case it means helping kids maneuver through life…i.e. move, sell. buy, marry, give birth…in other words, any time they need help, Mom is here to help. The years of “rearing them up” are over, but their lives get crazy and complicated and they still need guidance and a strong back!

Soooooo, what I have I been up to?

The house Matt bought was the home of his aunt’s sister…she passed away in March. So imagine you walk out of your home and die…and everything you own is in that house. Yep…and not only is it a big house, it was PACKED FULL! No one was able to really begin sorting and packing and moving her stuff out until after Matt closed so the week before Katie moved, I was at Matt’s new house sorting and packing!

After a few days of doing that, we loaded up a 16’ moving truck with all of Katie’s belongings and her cat, Simon, hooked her car up to the back, and drove 21 hours to her new home in Delaware.

I made an instagram post about this trip…one of the hashtags was #budgetrentalssmelllikeass…enough said about that issue.

The truck did not have cruise control. I never thought of that feature as being a “must have” on a vehicle. I was wrong.

I will NEVER complain about the condition of Arkansas highways again after driving through Missouri, Illinois, Ohio and Pennsylvania.

NEVER book a motel in a city if you have no idea where their “bad side of town” is….there is a good chance the hotel will be smack dab in the middle of it.

When driving a 16’ box truck towing a vehicle DO NOT get yourself in a tight spot…only get gas where 18 wheelers get gas!

All that being said, we were extremely fortunate to find parking right in front of her apartment. Fortunate as well that she has a friend who had moved to Wilmington the week prior and was available to help unload the truck. We were able to get everything moved into her little apartment the evening we pulled into town.

Then the REAL work began.

The apartment was advertised as 700 square feet…I can assure you it is not! “Tiny living” is a real challenge, even for a recent college graduate who has few possessions. Unfortunately, that is all that is really affordable if you are looking for a safe neighborhood close to downtown in an older Northeastern city.

You have to be very judicious about possessions, you learn to be very organized and you make the most of all the space available.

So for two days we unpacked, purged, built shelving, and arranged and rearranged furniture and “stuff.” It was a challenge but in the end she has a precious “home” that is perfect for her and Simon!

The kitchen was the biggest challenge. Katie loves to cook and she buys in bulk and stores everything in mason jars. Since the kitchen only had two upper cabinets, we spend the better part of one day just building shelves to hold her storage jars, dishes and spices. (All the photos are from my Iphone, and again, I am not a travel blogger!)

The living room wasn’t as big of a challenge since it wasn’t much smaller than her college apartment!

The pen and ink drawings are of the old train depot and old post office in Fayetteville…a little token of her college town.

She finally ordered pillow covers for her throw pillows. She learned from her mama…keep the big stuff neutral and infuse color in the decor…pillows, rugs, art, etc. The pillows she ordered are bright and fun and full of color!

Two days of driving, two days of moving/building/staging/purging and then the fun begins….

NEW YORK CITY BABY!!!!!

Yep, I finally got to take my baby to New York City! We took a train from Wilmington, Delaware to Penn Station in New York City, walked 10 blocks to our hotel and spent 3 1/2 glorious days in New York City!!!

Okay, glorious is a stretch….it rained the first day and they were experiencing their first big “heat wave” of the summer….weather-wise, not so glorious.

So what did we do in the rain and the heat? AS MUCH AS WE COULD!

We saw two Broadway plays….

It was the one thing I regretted not doing when Matt and I went to NYC.

We did the whole “Rockefeller Center” thing…bought a sweatshirt in the NBC shop, went to the Top of the Rock and had coffee in the plaza.

We ate a pastrami sandwich and a HUGE slice of cheesecake in a sweet little cafe off Time Square….

We rode bikes around Central Park….keep in mind it was pushing 100 degrees so we were pretty melted. That being said, when Matt and I road around Central Park two years ago, I had to walk 1/2 the way…I was just soooo out of shape! After losing 20+ pounds and biking for the last year, I was able to ride around the entire park without stopping at all! Yay, me!!!

We ate dinner in Bryant park, took the night bus tour across the Manhattan bridge to Brooklyn, walked across the Brooklyn bridge in the rain, visited the 9-11 memorial, took the ferry to the Statue of Liberty and Ellis Island. We took the extended tour of Ellis Island. We spent a morning in the Museum of Natural History (really should have spend ALL day there), took a bus tour of Harlem, saw Grant’s tomb, visited the Federal Hall where Washington was inaugurated and the little church across from the 9-11 memorial where he prayed after his inauguration. We took a water taxi up the west side of Manhattan. We visited the church were Alexander Hamilton is buried and of course, St. Peter’s Cathedral on 5th Avenue….

Which reminds me…how many Catholics does it take to change a light bulb….

Even in the most reverent places my mind goes places. But seriously, it is BEAUTIFUL cathedral!

I know we did much more…but basically we saw as much of NYC as we could in a few short days.

Then I flew home from Laguardia and Katie returned to her new little apartment in Wilmington.

My baby has officially “left the nest.”

And while I would love to sit and “muse” about this next chapter in my life, I really didn’t have much time to dwell. I had work to do at the apartments, a pile of projects in my garage, and a son who needed help with his yard and garage at his new house.

Man I need a vacation!

Maybe in the pile of projects in my garage I will have a makeover to share next week.

Until then….

Info

Comment

Bleaching in an HE washer...who knew?

I know I have been MIA but June was a crazy busy month and this month isn’t going to be any better!

This past week we traveled to New Braunfels, Texas for a little family reunion. Great fun visiting family, floating the Comal and Guadalupe Rivers and doing the “tourist” thing at the Alamo and on the River Walk in San Antonio!

I had a few major projects at the apartments the last few months!

We moved Katie out of her college apartment and all of her stuff is in storage waiting on her move to Delaware in a few weeks. She is there this week apartment hunting.

I’m not looking forward to driving over 22 hours in a big moving truck but after we get her settled we are headed to New York City for a few days! One of my all-time favorite places to visit and I have wanted to take Katie for years! We will take the train from Philadelphia to New York! Just too much fun!

Matt sold his “starter home” and will close on it and his new home this month…bigger house with a pool!

So…what do I want to share today.

Something that is LIFE CHANGING!!!!

Bleach loads with HE detergent.

As I have mention before, I love white bath towels, bath rugs, sheets, dish towels, and wash clothes…and of course I love my white cotton undies and Brian always wears white cotton t-shirts. My favorite thing about them all is the fact that I can bleach everything…clean and sanitary.

Right?

WRONG!

I noticed something weird when i went from a “regular” washing machine and detergent to a front load machine and HE detergent…the white towels and wash clothes always seemed to have “stains” that just never came out…makeup, coffee, chocolate…and the under arms of the white t-shirts always seemed “dingy” and never really “smelled” clean.

A few months ago we bought a new washing machine…we went from a front load to a top load…but it still uses HE detergent.

Side note: this is exactly why I didn’t put one of those nifty counters across the top of my machines when I remodeled my laundry room a few years ago…I THOUGHT I might eventually go back to a top load machine. Sure enough, I had my fill of front load washers. Maybe it was brand, but we had two machines that lasted about 4 years each. This time we went with a good ole’ “American made” brand…we will see how it holds up!

ANYWHO….a few weeks after we installed it i noticed it was making a weird knocking noise during the spin cycle…so I called and they sent out a repair person who promptly IDed the problem…the water hose was hitting the back of the machine during the spin cycle.

But the BIG news was that I found out WHY my whites didn’t seem to be getting as “white” and clean as I thought they should.

According to the repair guy, HE detergent and bleach DO NOT mix….basically if you mix bleach and HE detergent, the detergent will not “clean.”

Some machines dispense the bleach AFTER the wash…mine does not so I have basically been bleaching my whites, but not really washing them.

So now I wash my whites in hot water with the HE detergent….then I do a “rinse and spin” cycle with the bleach.

Adds a step to my bleach loads but it is well worth the effort!

Now, I want to qualify that this is what the repair guy told me. After a few months of testing his theory, I have come to the conclusion that there is merit to his madness.

My whites are whiter, the stains have disappeared and the t-shirt pits smell fresh and are no longer “dingy.”

So…there you go!

Hope this bit of information works for some of you…as I said, for me, it has been life-changing!

Info

4 Comments

Raspberry Lemon Cake recipe....

As I may have mentioned before, we have a big Sunday dinner every week. Yes, I bribe my children with food.

Sometimes only one will show up…sometimes they all come. We never know. I always cook A LOT of food…and usually the kids take home leftovers.

I always make a dessert and since I have a gluten-free daughter-n-law, I try to make a dessert she can enjoy. I have found a great gluten-free 1-to-1 baking flour…so I am able to make brownies, cakes and cookies gluten- free. Just substitute the gluten-free flour for regular flour…1-to-1. Personally, I can tell a “tad” difference so I usually make 1/2 gluten-free and 1/2 with regular flour. But I have found that the more flavor a dessert has, the less likely you are to really taste the difference!

This week I tried a new recipe…a raspberry lemon cake! SUPER yummy…

Get the recipe HERE and ENJOY!!!!!!!

Info

Comment

Updating outdated furniture...another "before" and "after" makeover!

You have it or you have seen it being sold for next to nothing on Craigslist or Marketplace or at garage sales.

Dated furniture. Naturally we turn our noses up at it because, well, ick.

But often these old dated pieces are rock solid and truthfully, they can be updated with very little time, money and effort. You just have to be willing to see past the “ick” and roll up your sleeves.

The first thing I did to “update” this piece was remove the little scrolly doo-dads on the top drawer and round doo-dads in the corners.

Often these little “doo-dads” are affixed with a little bit of glue and tiny nails…just use a chisel or flat object to slip behind and pop off…super simple…then just fill the holes and sand smooth.

After that I removed all the hardware. I liked the little brass knocker looking pulls so I painted them (and the round knobs on the top drawer) with metal primer and Rust-Oleum’s Oil Rubbed Bronze spray paint. I replaced the bottom two drawer’s hardware with oil rubbed bronze cup pulls…

While the hardware “cured” I painted the piece with homemade chalk paint. Two coats. Homemade chalk paint is SUPER cheap and easy to whip up…5 tablespoons of Plaster of Paris mixed well with 3 tablespoons of water…then add 2 cups of latex paint. You can buy sample pots of paint so you can mix the chalk paint any color you want. Then I “distressed” a tad with 220 grit sandpaper, wiped it down with tack cloth and sealed it with a spray on polycrylic.

So what does it cost to update a piece like this?

Time wise? A day. Chalk paint dries super fast so you can usually apply two coats and distress in a matter of a few hours, then spray or brush on a sealer.

Cost?

Wood putty/filler. Maybe $3-4 but then you have a BUNCH for other projects.

Spray paint for hardware. 1 can of metal primer and 1 can of spray paint…less than $10…and again you will have a bunch leftover for other projects

Paint for the chest. Home made chalk paint is super cheap. A box of Plaster of Paris is about $5. A sample pot of latex paint is less than $4.

Clear coat: polycrylic or polyurethane or any spray on clear coat…less than $10.

In this case I added new hardware on the bottom two drawers…that added about $20 to the total cost…but the original hardware could have been painted as well.

A piece of sand paper and tack cloth…less than $5 if you don’t have it on hand.

So realistically WELL under $50 and a little time and effort.

Seriously…soooo simple!

I have said it before and will say it again…LIFE IS TOO SHORT TO LIVE WITH UGLY FURNITURE!!!!

You CAN do it!

Info

1 Comment

A simple "before" and "after"....

A simple and inexpensive makeover.

Before….

After….

A little homemade chalk paint….5 tablespoons of Plaster of Paris and 3 tablespoons of water, mixed well. Add 2 cups of latex paint. Two coats…a little distressing…sealed with polycrylic.

The hardware wasn’t anything special…I primed it with metal primer and hit it with some blue spray paint I had on hand…could have been black, teal, white…whatever…not sure I am loving the navy but it would be easy to change it!

Simple, inexpensive…but oh so much better!

Remember, LIFE IS TOO SHORT TO LIVE WITH UGLY FURNITURE!!! YOU CAN DO IT!

Info

Comment

My happy place....

This month has been crazy busy. I started painting the older buildings at my apartment complex…the weather hasn’t been very cooperative so only 1/2 is done. I have had to tear out and replace rotted flooring in an older unit and I have had a few vacancies which is always a lot of work. My daughter graduated from college week before last and everyone came home (I shared that here) and my grandson graduated from high school this past weekend.

Crazy busy!!!

One thing I am eternally grateful for is my yard…it is my happy place and I am so glad I got all the mulch down and the planting done before life got too hectic.

One of my favorite ways to unwind is sit in my backyard and just breathe….

Not much changes in the front and side yard but since my neighbors murdered their trees, my swing pergola in the front gets too much sun in the afternoon to really enjoy….

…but again, visitors may not see your backyard but they will see the front…so keep it pretty! (I shared the construction of the window planters HERE)

I do have a few moles causing a bit of stress….HERE I talk about what I have learned about moles and how I deal with them (it ain’t pretty!)

But since I now plant all my “tender annuals” in pots, they really do little but annoy me. Truth is they are nature’s little tillers for flower beds and if they didn’t run through the yard to get to the flower beds, I probably wouldn’t give them a second thought.

I am grateful I have the ability to do the work I do…but I am even more grateful I have a place I can go to recharge….

Info

2 Comments

Another new dining room table and the greatest Mother's Day gift....

ANOTHER dining room table…obviously I have a soft spot for chairs and tables. When I saw this pathetic trestle table at a barn auction a few weeks ago, I just knew she had some serious potential….

The top was in pieces and the finish was crud…but oh the potential. And it wasn’t until I got her home that I discovered her little hidden secret…

She has this super nifty fold out “leaf.”

Just too fricking cool!

In spite of the fact that I have been up to my earballs in work at the apartments, I couldn’t wait to start working on her. The first thing I did was strip all the old finish…HERE is the process I used. This is a tried and true process that makes quick work of a daunting task!

After all the old finish was stripped off I had to glue and clamp the table top back together….

I always make my repairs AFTER I strip but before paint or finish…and I always make sure I make all the necessary repairs. No sense in making it pretty if it is just going to fall apart…glue and clamps!!!

The top was solid (vs. veneers) so the pieces were a tad warped…no biggy…I clamped it as well as I could and then I sanded the joints smooth…starting with the finer grit (220) and working my way down to a rougher grit (150) and then back up to a finer grit, before applying a tung oil finish.

Tung oil finish is my “go to” finish for many reasons…it is super easy to apply, it is super durable and it is super easy to reapply when the finish gets scratched or begins to dull!

So, when all was said and done, this little table will now take her place in the dining room….at least for the time being….it is no secret I swap out tables on a regular bases….here are just a few I have featured over the years…

A Duncan Phyfe….I gave it a little makeover HERE before selling it….

An antique trestle I featured here…

An oak farmhouse table featured here…..

The most recent…an antique draw leaf table…

All these tables have one thing in common…they are relatively “compact” but can be expanded to handle Thanksgiving dinner. Basically once a year I need a large table…and these all fit the bill.

The newest little trestle table is compact, expands, and beautiful!

So get ready for a few pictures…..

I just LOVE the new light fixture from Wayfair I featured here….

I love how it can easily be expanded. No more having to find a place to store leaves or hauling them out for one dinner…just slide open the top and fold out the insert…simple (especially after a little WD40)

One huge problem….I REALLY dislike the Duncan Phyfe chairs with it…they just don’t look right…and sadly I know exactly what chairs I want for it and I have had them and sold them a few times over. The good news is I will eventually find what I want….

Until then I bought this little piano bench at the same auction. Again, pretty cruddy…

…but I stripped and oiled the top, scrubbed up the brass feeties and painted the base with my new favorite blue…the same one I used on the buffet (here)…

Meh….not really “swooning” over it, but it will serve the purpose for now…until I can find the chairs I want or another pathetic little table catches my eye. I wouldn’t take bets on which happens first!

THE GREATEST MOTHER’S DAY GIFT

This year I received the absolute best Mother’s Day gift!!! Another college graduate.

My youngest daughter, Katie, graduated from the University of Arkansas with a degree in Bio-Engineering.

She is beautiful, smart, and talented…and I could not be prouder.

She, as well as her brother Matt (Masters 2015), are fourth generation Arkansas graduates….my great grandmother graduated in 1920, my grandfather graduated in 1943, and I graduated in 1987.

Brian and I are now 5/5….five kids, five college graduates. And the fact that all five were here for Katie’s big day, which happen to be Mother’s Day weekend, made my day extra special!

Info

2 Comments

Vintage car handle hardware...

I am trying desperately these days to be a bit more “creative” and get out of my “everything white” funk.

I saw a really cute idea on Pinterest….vintage car handles as hardware. Naturally I jumped on Ebay and began searching for vintage car handles. I looked back at my Ebay history…I ordered them in JANUARY!!! Didn’t have anything in the works, just thought is was a cute idea.

Did I save the link to the “inspiration?” Um, no. Did I have a plan in mind as to how to attach them to a drawer front.? Um, no. Did I have a table to even attach them to? Um, no.

Just thought it was a super cute idea.

The first thing I had to do was figure out how to attach the handles to a drawer front…the hole in the backside is not threaded. My original plan was to find a bolt that fit snuggly in the handle hole, then just use JBWeld…love that stuff. The problem with that is it would make it darn near impossible to remove the handles in the future. Not MY problem, but as I have said before, I want buyers to be able to makeover the piece again in the future.

Thought maybe I could JB Weld a light fixture bolt (threaded on both ends) into the handle, then just add a nut and washer…hum….that could work and still allow for removal in the future.

While I was at Lowes scouting bolts one of the nice associates showed me this nifty brass insert thingy….

Because brass is “soft” you can screw this little plug into the hole (using a flat screwdriver), then get a bolt that will fit the inside of the plug…in this case a 5/16 hex bolt. I slipped a washer onto the bolt so that it would sit snuggly against the back of the drawer.

Problem 1 solved.

Problem 2 is finding the perfect little table…fortunately I found a cute little solid wood side table at a garage sale for a few bucks….

Problem 3….as you may have noticed, the handles have a 1” “bump” on the backside which would make it impossible for them to sit flush on the drawer front.

I removed the little wood handles on the drawer fronts and puttied the little holes.

I took a 1 3/8” paddle bit (I couldn’t find my 1 1/4”) and made a hole in the front of the drawer front deep enough for the handle to sit flush. Then I used a 5/16” drill bit to make a hole in the center of that hole for the bolt.

TIP: To make sure you don’t drill your large hole all the way through the drawer front, wrap a piece of blue/masking tape on the paddle bit to indicate the depth you need to drill. (Not pictured)

Now I was able to set the car door handle flush on the front of the drawer and run the bolt (with washer) through the backside and into the little brass plug.

Since I knew the bolt may “loosen” and there is only one bolt holding the hardware in place, I added a dab of construction mastic (liquid nail will do) to the hole just to give the handle some stability.

Before applying the hardware, I primed, sanded, tacked and painted the table a high gloss red (See HERE why I can no longer call it my KSTP process.) The insides of the drawers were a tad cruddy so I primed those as well and painted them black…not necessary but kinda cute!

I found some “L” shaped metal floor trim and decided to add it to the front corners of the little table….installed the new door handle hardware….and presto bingo….

Too stinking cute!!!!

And now that I have figured out all the logistics to turning vintage car handles into hardware, grab a few and have some fun!!!

I have a few of these door handles left…now I just need to find another little table or small dresser!!!!

Info

Comment

Craftsman dresser....

I have said it before…”Imitation is the sincerest form of flattery.” Unfortunately, not every one likes to be “imitated”…or “copied.”

But I have to wonder…why do others post projects on blogs or Pinterest if not to give inspiration…inspire others to “imitate” their creativity.

I have NO problem with others “imitating” my creativity…imitate away! This entire blog is here to inspire you to make your home more beautiful. And if you are looking for inspiration for projects you intend to sell, help yourself….there are A LOT of people out there who couldn’t paint a piece of furniture or hammer a nail if their life depended on it. They need your abilities and creativity and if I can inspire you to create for others…yay me!

I try desperately to give credit where credit is due…if something “inspires” me I try to link back to the site. Unfortunately, I am the world’s worst at seeing something I like, “drag and dropping” the photo into my “inspiration folder” and not actually saving the link. I really do try to go back and find where the photo might be posted, but I can’t always find it! Same with recipes. I’ll see one I like, print it off and then I can’t find the original recipe.

Fortunately, this time I not only have a picture of the inspiration, I also have the link….HERE! (This dude has some mad woodworking skills and his dresser got some heavy duty reconstruction.)

The minute I saw this little dresser/changing table I knew I had to do one.

Fortunately I found a dresser that had perfect wood detailing on each drawer that allowed me to paint the “silver handles” rather than add new detailing. I also didn’t do any “reconstruction” on the piece other than adding bracing and wheels.

You can buy these wheels at Lowes…they just screw on!

Unfortunately, this is where I have to admit AGAIN what a bad blogger I am because I failed AGAIN to take a “before” picture. Suffice it to say, it was just a plain ole’ fake wood grain dresser…perfect for a little makeover!

Other than the wheels, the only other thing added was the “Craftsman” decal…believe it or not you can buy them on Ebay…HERE.

I found a red gloss spray paint that is a perfect match for the “Craftsman red”….the black on the drawer fronts is black lacquer…and of course the silver is just “stainless” paint. I primed the entire piece with primer, sanded well and wiped it down with tack cloth…then paint (KSTP).