Lazy days....

This heat is brutal...I hate to gripe because my son reported it was 120 degrees in Phoenix a month ago and I usually we are in triple digits by now. But seriously, this heat and humidity is brutal.

Because of that I get a tad lazy.

First, I want to hibernate...seriously, go inside and not come out until October. Second, I tend to do stupid things....

Like take this little mahogany bookshelf in without doing anything to it....

Not horrible and I really thought just MAYBE someone else would take a risk on it. But it did have several issues.

First, the overall original finish...kind of cruddy!

Not horrible, but not great either.

The biggest issue was a "burn" on the veneer,. Seriously, how does this happen?

I have no idea!

I brought it home after it sat in my room at 410 Vintage for a month or so...evidently no one was willing to do their own DIY on it. So it was up to me to make it presentable...curses!

First, I had to repair the burned veneer (again, what the heck?) I used the same process I used on the old dresser and shared here.

I really wanted to save a little bit of the wood feature, so I used this process to strip and oil the top. Didn't take but a few minutes!

Plaster paint, distress and seal.

I want to admit one little glaring error in this little makeover. Mahogany has a tendency to "bleed" through any paint. The BEST thing to do when painting mahogany is to first seal it with a clear lacquer or primer, then apply your paint.

I, sadly, did not do this. And while my little "repair" job on the veneer is darn near perfect, the fact that the mahogany bled through makes this little oversight a little more glaring.

You can clearly see where the patch is and where the original finish bled through...I'm blaming this one on the heat too! I know better.

Oh well...guess I'll just drag it back in the house and give it ANOTHER little makeover...curses!

Info

2 Comments

The chest of drawers from hell...

Last week I told you not to be afraid of a sturdy piece of furniture that needs a little repair.

I think the key word is "little."

THIS monster needed more than a little!

Here is how this happens. I want something at an auction. They open bidding on one item, like this HORRID old dresser. I don't want it but neither does anyone else...so they add something...I don't want that either...neither does anyone else...so they add something...I don't want that either...neither does anyone else...so they add something...I WANT THAT! But in order to get it, I have to take all the other crud. So I ended up with this ratty chest of drawers, a disgusting trash can, a burnt orange smelly couch, and the ONE item I really wanted. I started to leave this chest, but I noticed it did have MOST of it's parts, and some stunning hardware.

It also had a serious case of ugly and some water damaged and splintered veneer on the top and at the bottom.

Hum....I can fix that...all because I thought the hardware was kind of nifty!

Seriously, what was I thinking?

I loaded it up and brought it home and went to work...and work it was. But this is a great opportunity to show you how to make the best out of the worst!

The first thing I did was remove all the drawers (and pieces of drawers) and the hardware and set those aside for the time being. The drawers needed some repair and the hardware needed to be painted. But I had bigger issues to deal with and unless I could deal with those issues, spending time on the drawers and hardware would be a waste of time!

The top...wow. Normally I would have just removed and replaced the entire top, but structurally the frame on this one solid. It just needed a new plywood top.

So I removed the old plywood top. Not a biggy...it pretty much popped off. All I had to do was take a chisel and scrape off a few chunks that stuck and some adhesive residue.

I took a piece of 1/8" oak plywood and laid it on the top, face DOWN, and marked the outline of the top with a pencil.

Veneers and plywood WILL "splinter" when you cut it...so the trick is to ALWAYS score it with a sharp utility knife. Once you score it, you will use the appropriate tool (in this case I used a jig saw since the front edge was curved) to cut on the OUTSIDE of your score line.

I scored on my pencil mark, then cut on the outside of that mark.

Once I had it "rough cut" I applied it to the top frame with wood glue, set some heavy items on it, clamped the edges to the top frame and let it dry over night.

After the glue had dried well, I took a belt sander with 50 grit paper and sanded the edges of the plywood. When I got within 1/8" of the edge, I used my mouse sander with 120 grit to finish up flush with the edge of the frame.

I used my thumb to "putty" on a little wood filler along the edges, sanded smooth, then I primed it with Kilz.

The other issue with this chest was the "veneer rot" at the base. I scored the veneer with a utility knife above the highest point where the veneer was "loose." Then I just peeled the loose veneer off. No need to remove all the veneer if it is secure!

I nailed a 1x4 board along the bottom to improve the stability. I used scraps of the veneer I had removed to "shim" it. I did this on both sides, even though only one side had issues.

Now it was time to "fill in" the missing veneer. For that, I used wood filler and a broad knife. This is where a little creativity and patience comes into play because you will NOT accomplish a smooth finish with one coat! In my case it took THREE shots to get a nice smooth finish. I applied a coat of wood filler, let it dry, sanded, wiped, and then applied another coat. Same process...three times before I was satisfied with the results!

Once the last coat of wood filler was sanded smooth and I was satisfied with those results, and ALL the other little repairs were made and I had cleaned it all well, it was time to give the "box" the old KSTP treatment...Kilz, sand, tack and THEN paint.

The drawers...all but the top drawer were present and accounted for but they all needed a little glue and clamping! Remember, WOOD GLUE AND CLAMPS are your friend...not nails and screws. I pulled a few of those as well as scraped off silicone someone had used to "fix" the drawers!

I only had the front and the bottom of the top drawer. My initial plan was to make a little open shelf in that top space, but I decided to build and replace the drawer! Not a biggy for me since I have built drawers before, but you may want to consider making an open shelf if you are missing a drawer, or one is too difficult to repair.

I primed the inside and sides of the drawers and will paint them as well. This is the best way to "kill" the smells that sometimes penetrate drawers and hide years of use and abuse!

I was super excited about the hardware...very unusual! But it was pretty cruddy so I decided to paint it gold. It is NOT hard to update hardware with paint! First make sure you reinsert the hardware screws. This is important so you don't get paint on the threads of the screws or in the screw holes of the hardware. Second, PRIME!!! There is primer specifically for metal, so make sure you prime with the proper primer. I prime both the back and front of the hardware. You may want to sand a tad after you prime just to knock off the "crumbs." Then just spray on whatever paint you want to use. In this case, I used a gold metallic paint to give them a nice gold sheen!

(You may notice I am missing one of the smaller pulls...I noticed that too! Found it in the yard...not primed or painted...curses!)

If you are going to change the hardware on a piece of furniture, you will want to use wood filler to putty the existing holes and sand smooth BEFORE you prime and paint (again, it may take 2-3 coats) That way you are not limited by the size or placement of the existing hardware! Then just drill new holes for the new hardware!

The repairs were pretty extensive on this ratty old dresser but in the end, it really was worth restoring! At this point it is repaired and primed and ready for a final coat of paint.

The sky is the limit! I will probably paint this dresser the same color as a few other projects I am working on, so right now it will sit until I am ready to paint several things. Part of the "assembly line" process!

Again, don't be afraid of doing a few little repairs...in the end, the process will always be worth the effort if you take the time to do it right!

Remember this process...make ALL necessary repairs first and clean the entire piece! Then KSTP! Kilz (or whatever primer you prefer), sand, tack and paint!

I will share this piece once I get it painted. But even at "base neutral" it's looking pretty good!

Info

3 Comments

Another mid-century chair....

I don't know too many people who would see this ratty old chair and swoon....

...but swoon I did. And to make it even better, there were TWO of them! Yes, two.

Katie TRIED to claim them both but I had to keep one for myself!

The cushions are the original black naugahyde, which is super common on mid century chairs. Fortunately they were in pretty good shape...not perfect but close enough!

All I did to both chairs was strip and oil using this process, scrubbed and applied Armor All to the cushions, and BAM....BEAUTIFUL!!!

I told Litty to move so I could take pictures and even nudged her with my foot. One thing about cats...they don't mind well! (A friend told me they had mice...I told him to get a cat...he told me he didn't like cats...I told him the cat wouldn't care!)

Someday I will actually learn to use my camera so you can really see the amazing grain detail in these pieces!! Beautiful!

One of the chairs had a little "boo-boo" on the back...a little glue and some clamps fixed it right up! No biggy! DO NOT be afraid of a sturdy piece of furniture that needs a little repair...if you take the time to do a little "google" search and watch a few Youtube videos, you can pretty much repair anything properly!

Soooo....I kept one and one went to Little Sister's new condo. Next week I hope to share the desk I made her, the tufted chair we upholstered and a super cool coffee table she refinished! Her first place is shaping up to be super cute and this little chair was an awesome addition!

Until next week....

Info

2 Comments

Heirloom stool....

I know I probably sound like a broken record, but I don't decorate with just anything...the "stuff" I decorate with has to be things I love or heirloom pieces!

A few years ago I picked up a couple of stools and dolled them up a bit and featured here.

The one I liked most was the one with the birdies...but every time I wanted to open a kitchen drawer I had to move it. So I sold that one and have been using the yellow stool.

But this past Christmas, when I was hauling decorations out of my packed attic, I spied an old stool that had belonged to my great-grandfather. I believe it was the stool he used at his drafting table. I have had it for years but it was in pretty bad shape, so I had stuck it in my attic and pretty much forgot about it.

I finally hauled it down to the garage and decided to give it a little makeover. The first thing I had to do was strip and oil the oak base using this process.

I had a little leftover fabric from this chair project so I decided to use it to recover the seat.

Did I take a "before" picture...um...no. Just imagine...old, dated, well used.

The upside is it fits perfectly under the kitchen drawers. Now I can use this precious family heirloom!

Oak is not my style...but anything that belonged to family is...another "thing I love."

HAPPY BIRTHDAY KATIE!!!!

I want to take a minute to wish my precious, beautiful, smart, funny, talented youngest daughter a very happy 19th birthday...I can't believe you are entering your last year of teenhood! I have no doubt this next year will be as amazing as the last 19! You make a mama very happy and proud!

Info

Comment

Entry and stairway makeover reveal....

I started my entry way makeover here when I shared the "demo" of the coat closet! I did not realize this "weekend" project would drag out for TWO MONTHS....but that is pretty much the speed I work at around here these days!

Time flies when you are having fun!

I had intended to post this project last week but Brian had to have shoulder surgery so his care has taken up a bit of my time. (Someone explain to me why a 53 year old man feels the need to bench press 275 pounds...even if he can!)

Truthfully, it is not fun to demo and construct in a house you are living in. I put up plastic when I did the major sanding on the sheetrock...

... but there always seems to be a little spot here and a little spot there that needs just a little bit of sanding...before you know it it looks like a dust storm has blown through your house!

Truth be told, this "makeover" actually started YEARS ago when I removed all the carpet from my stairs and put down oak treads and risers. I knew the day would come when I would not want to haul a vacuum cleaner up and down the stairs (that day is here!) so I wanted hardwood stairs!

My house had the typical "rough construction" stairs with pine treads and risers, covered in carpet...you can kind of see how they were constructed, and what I discovered when I pulled the carpet, in this picture....

It really was not that difficult to install new treads and risers. The biggest "hum" was finding that the 2 x 12 tread (the horizontal board you step on) lipped over the riser (the vertical board facing each step) by 1/4". To solve for that, I just applied strips of 1/4" board to the bottom of each riser and then faced them with new oak boards, cut to fit. Most home improvement stores carry prefab oak treads. I cut each to the width I needed, stained and sealed them, applied construction mastic and then nailed them into place. I applied one final coat of poly after I had installed them. Obviously I did a good job, since it took me TWO HOURS just to remove TWO of the stinking things!

Since I was installing new travertine tile in the entry, I decided now was the time to also make some changes to the newel post and bottom steps.

As with EVERY project, the first thing I did was "find my inspiration." That was not difficult since I knew from the minute I laid eyes on Cassidy's stairs on Remodelaholics.com that this was what I wanted....

One of the things I really love about her staircase are the colors...the stain and the paint. Sadly THAT little detail is going to have to wait at my house. My staircase was stained to match the living room floors, which are going to be here a tad longer ...and while it isn't "technically" honey-oak, the "butterscotch oak" isn't really my cup of tea these days. But again, it is going to have to wait for now...the thought of taping and staining and painting everything right now is more than my brain can process!

This is one of the important keys to remodeling any space...identifying what you can do (physically and financially) NOW to enhance the space...and patience! I knew I wanted the "openness" of the bottom two steps and a larger newel post. Those are things I needed to do before I installed the %$(@# travertine tile (Honestly, don't ask how much it cost. I have NEVER in my life paid THAT much for tile, but I wanted it and it is a small space...so I splurged!)

While I had intended to post a "tutorial" on this project, I realized it is like many home improvements...a puzzle that will probably differ depending on how your home was constructed and what materials were used.

So let's start at the beginning...what WAS there.

A tight entryway that required us to lift anything over 28" wide over the newel post!

A coat closet that was NEVER used and was basically just a dumping ground for anything and everything! Hardwood flooring...NOT a material one should use by an entry door. Over time wet feet will do a real number on it!

An anemic newel post that pretty much screamed 1999!

So were does one begin a sizable project like this? Again, how do you eat an elephant? One bite at a time!

So the first thing I did was demo the coat closet and remove the smaller built in bookcase...gut wrenching details here.

After the closet was gone I had to deal with moving electrical wires...a major chore for me and I would honestly suggest most call a professional. My electrical professional is my son-in-law, but since they live 2 1/2 hours away, this is another project he talked me through over the phone! After all the electrical was moved and I could move around in the space without whacking my head on dangling switch boxes, I removed the existing baseboards and hardwood flooring.

Easy right? Um, no! First I had to mark and cut a line with my skill saw where the new flooring would meet the existing hardwood. Dust storm number one! Then I had to scrape up all the old flooring and mastic...seriously, I think you could safely attach wings to a plane with that glue!

Next, I tackled the sheetrock repair and texture...hence the tarp to prevent a MAJOR dust storm!

Since I was basically "patching" the sheetrock where I had removed the closet walls, I used this process! I can not stress enough how easy sheetrock repair can be if you follow these steps. Since the area I needed to texture was much larger than just a little patch, I used a "sheetrock hopper" to blow texture on the walls. I actually had a painter friend come over and help me with this step since he is a master at using the hopper and could "blend" the old with the new seamlessly!

Then paint! I can't say it enough...there is a huge plus to knowing the exact formula for your paint. Someday soon I really want to repaint my downstairs....someday! Again, can't wrap my brain around that chore! But knowing exactly what I painted the walls with 8 years ago allowed me to paint the new patched areas and blend it with the "old."

After the walls were repaired, textured and painted, it was time to tackle the BIG project...the staircase. That had to be done before the new tile could be installed because I was moving the existing newel post that sat at the bottom of the stairs and extending the bottom step, which changed the layout of the flooring.

The first challenge...matching the existing stain color (as much as I dislike it!) David, at our local Sherwin Williams, usually does a bang up job of matching existing stain. He did an AWESOME job on my kitchen stain! This time even he struggled. I think the biggest problem is that the original clear coat is poly...and poly "ambers" over time, which deepens the color. I ended up using David's "match" mixed with a premixed stain and final got a decent match. I stained and sealed all the pieces before installing!

The next big head-scratcher for me was figuring the exact angle and method to cut the existing bannister, trim and bottom rails without removing it all. After much hymning and hawing and measuring and drawing, I drug out every power tool in my arsenal and made the cuts! And did a little sanding to get a good tight fit! MAJOR dust storm!

I also had to build a new "base" for the wider bottom step. As I said, it's a "puzzle" and sometimes you just have to measure, figure, plan and execute as you go...when you are meshing new with old it can be a little more challenging than starting from scratch!

Again, I could post a long drawn out tutorial...but honestly Google and youtube are all you need. You will find much better videos and tutorials than I could ever provide.

And this is pretty much how it sat for another week. Why...because the old adage "measure twice, cut once" only works when your brain computes properly at least once...if it computes improperly BOTH times, you will cut your special order materials wrong and have to wait on them after you reorder them!

As soon as my special REorders came in and I was able to finish up the two steps and newel post, I installed my travertine tile. Then...it sat...AGAIN!

Why...well because I couldn't decide whether I wanted to add a little trim detail. I contemplated shiplap...maybe a decorative wainscoting...or maybe board and batten.

In the end, I went with the board and batten. I'm not totally swooning over it, but it is a nice little touch (again, find a GOOD tutorial if you plan on adding this...there are hundreds of great ones out there in blogland!)

Soooo....drumroll......get ready for a lot of pictures!

Okay...you may notice that other than a funky rug and the little walnut table, there isn't any "froo-froo" yet. As I have said before, I don't decorate for poops and giggles..."stuff" has to have some meaning or be something I truly love...and so far I haven't found either for this space!

Eventually I also want to change/add lighting... I'll know it when I see it!

I seriously love the travertine tile. I laid it in a "brick pattern." It is a 12x24 tile so I staggered it 8-16-24". I also sealed it both before grout and after, which in my opinion, is a must for travertine!

I still need to put one more coat of poly on the bottom two steps and the newel post but I am waiting until Matt is gone for a few days so I don't have to worry about anyone going upstairs!

HUGE difference!

While I was making a few entry changes, I thought it was about time to order a new rug for the living room. The old one was only two years old, but with the addition of the new living room chair and post-Cleo-puppy, it was time! I decided to go with simple and neutral this time!

Aside from the wall paint I want to change, and the "butterscotch oak" I would like to restain, and the new hardwood floors I want to install and the new lighting I think would look good in the entry, I'm pretty darn happy with the changes.

One upside to the "dust storms" this project created was it forced me to "purge" ALL my bookcases, even the ones in the den and my room....dust goes EVERYWHERE when you project! I had to pull all the books to clean so I decided it was time to get rid of 30 years of collecting! I saved two collections of my favorite authors (most notably my autographed John Grisham collection...thank you Matt!) and a few of my favorite books, but over 150 hardback books will soon be finding a new home...right now they are packed in egg boxes in my dining room! Now most of my shelves are scantly decorated with antique books, framed photos and a few family heirlooms!

Ahhhhh....room to breathe.....

Info

5 Comments

Mid Century Chair Makeover and the trick to sewing vinyl!

Recently my mother has been on a purgefest. As a result, I have inherited a few beautiful pieces of furniture and several sets of family china.

This little table was one that belonged to my paternal grandparents and is the catalyst for my entry makeover that I will finally share next week.

Not really my style, but again, it combines two of my first loves....heirlooms and walnut!

This little chair belonged to my maternal grandmother...so when my mom offered it to me I honestly could not get it in my truck fast enough! THREE of my first loves....heirlooms, mid century AND walnut!

(Again, excuse the quality of the picture...this is from my phone!)

As much as I would love to keep it, Katie tagged it for her condo. Since neither of us were real keen on the finish or the fabric, I immediately put her to work stripping and oiling the frame using this process and finding a new fabric for the cushions.

After looking online at similar mid century chairs, she decided to go with a "leather look" white vinyl. Beautiful, but the fabric has one serious drawback.

It wouldn't go through my old sewing machine! (When I say old, I'm pretty sure I bought it before my oldest son was born...28 years ago!)

I have used vinyl and naugahyde before, but always for recovering chair seats...like these mid century dining chairs! I had never actually used it for a sewing project. I discovered that the vinyl-like material was NOT going to glide through a sewing machine, which posed a real problem when one needs to make new covers for a cushion, including all the piping!

My uber smart, engineering minded daughter came up with a perfect (all-be-it tedious) solution. Wax paper!!!! I encased the strips of material I was using to make the piping in strips of parchment paper (that's what I had on hand and it worked just as well!), and it went through the machine like butter!!

Since the vinyl had a fabric backing, it was not an issue to sew the cushions together since I was sewing the fabric front to front...so the back of the fabric was what was feeding through the machine. The only real problem was when I was making the piping because I was having to sew on the top of the fabric....that is where the parchment paper came in handy!

I covered the old foam with new batting just to give the cushions a little extra loft! Eventually Katie wants to add two little "button tufts" to the back cushion!

After all the tedious machine work, the cushions turned out beautiful!

Katie has stripped and oiled her new coffee table, I built a little entertainment cabinet and coffee bar and we still have another little tufted barrel chair that needs to be reupholstered. Move in day is this weekend so we may not have everything done but we are getting there! I have been buying kitchen ware at auctions and thrift stores and their kitchen should be well stocked! Exciting time for my baby girl!

And when we get done with all our little projects, they will have one groovy pad! (did I just show my age...lol!)

Until next week when I FINALLY share my entry makeover....

Info

3 Comments

Serpentine dresser makeover...

I want desperately to share my entry makeover, only because I want desperately for it to be done. Week 5 and I am STILL waiting on materials...specifically ONE stair tread that somehow did not get ordered properly. I have one, I have all the risers, I have a new newel post, and the tile was delivered over two weeks ago. But like so many of my home DIY projects, there is one little element that isn't here and I desperately need to finish. Pooh!

So today I will share one of the pieces I told you about a month ago!!! I picked up several wash stands and dressers at an auction and all were in desperate need of a little "DIY magic!"

First, and most important, always make sure whatever you are getting ready to spend your time and money on is in good repair. This little serpentine dresser needed some glueing and clamping before I could get down to the business of making it pretty!

It wasn't in horrible structural condition...just needed a little glue and clamping in the back and a few of the drawers.

I used this process to strip the top...again, I have to have my "wood fix." These tops are super easy to strip and if the color isn't just right you can always apply a coat of stain....I added a coat of walnut stain to this one! Then just oil or poly, depending on your preference. I prefer tung oil finish but for resale I often use poly since most people know how to care for poly finishes!

I didn't fill the gaps or sand out the "imperfections" ...I wanted it to look like what it is...a solid old oak top!

The drawers and cabinet could have been stripped and refinished as well, but for resale I kind of have to "go with the flow." Paint is the "thing" right now so I gave it a few coats of plaster paint, distressed and then sealed with poly. Again, I never wax a piece and poly has just enough "yellow" to give the paint an "aged" look!

Simple new hardware, and it is good to go for another lifetime of use!

Pretty!

This is a busy and exciting week around our house! My youngest daughter finishes up her first year of college and will be moving home until her condo is ready next month. My oldest daughter...wife, mom, part-time paralegal...will be graduating (WITH HONORS!) with her associates degree on Saturday. So proud of both my precious girls!

The last time my oldest son was home, we managed to get a picture of all five!

Yes, they are as amazing and awesome as they look! I know this past weekend was Mother's Day, but these kids make me feel loved and special EVERY day!!!

Info

5 Comments

Reviving old cutting boards...

I have featured old cutting boards on several occasions...here and here. They are relatively easy to find and simple to "revive!" And super cute to decorate with!

If you check out my kitchen reveal you will see I use them in several places in the kitchen...as a little chalkboard, as a recipe holder and for a back drop in my "baking corner!"

As I have said before, I don't use wood cutting boards in my kitchen...I prefer the marble and vinyl cutting boards for sanitary sake. But old wood cutting boards can add a real touch of warmth to any kitchen and you can often find them in a variety of woods...maple, mahogany, walnut, and oak!

This first board is a tiny little thing I found in a box of auction goodies. First I stripped the board using this process, then I chalk painted the handle and distressed it a bit and then I added a little something extra!

Adding this little transfer was super simple. I printed out the design, traced it onto the board using sewing trace paper...then I used a black sharpie to draw it on the board.

I used a design I found online, but you can find hundreds of awesome designs and transfer methods on Graphics Fairy!

After applying the transfer, I applied three coats of Watco butcher block oil on the board. Since I don't use (and don't recommend using!) the board for it's intended purpose, you could just spray the board with poly, but I like the natural and rich look of oil!

The next board is another little auction find...and old mahogany board that had been well used!

Stripping this board would not have removed all the cut marks so I took the sander to it...220 grit to get rid of the cut marks, then I finished it with 220. Super simple since mahogany is a relatively "soft" wood! I cleaned the little metal "stem" then I oiled the wood with butcher block oil (3 coats)...beautiful!

These little butcher block makeovers are simple and a great way to add a little "whimsy warmth" to any kitchen. Next time you spy one in a thrift store or at a garage sale, don't pass it up just because it looks a little warn and ratty! Take it home and spend just a few minutes bringing it back to life...you won't be disappointed!

Info

Comment

Drop door cabinet makeover....

Enough about my entry makeover FOR NOW! I'll get there eventually but I'm at the "wait" and "hum" stage...waiting on tile and stair treads and not quite sure what I want to do about trim and lighting...hum....

So in the meantime I thought I would share one of the wash stands I rehabbed. I went to an awesome auction several weeks ago and brought home 5 potentially beautiful dressers and wash stands. One just needed to be cleaned and oiled but the others needed some serious work.

On these older pieces I just can't bring myself to slather them entirely in paint. I always have to restore a little bit of the original wood. I know in today's world of home decor, paint is all the rage, but I need a good balance of paint and the "warmth" of wood. So no matter the condition of the top, if it is solid wood, I am going to strip it and refinish it.

This little cabinet was originally a "wash stand." It wan't in terrible shape but it had seen better days!

It had a little mirror on the back, which when removed left a "gap" along the back edge.

If I was going to paint the top, I could have filled it in with a strip of poplar and been done with it. But I knew I wanted to refinish the top so I added a piece of oak...

...just routed the edge, then attached it with glue and trim nails. I stripped the top with this process, applied a little walnut stain and sealed with poly!

I chalk painted and distressed the base and sealed with poly. The little drop front REALLY distressed, but sometimes I just let furniture do what it wants to do! A little update on the hardware and it is good to go!

The drawers on most antique pieces have some issues....remember GLUE AND CLAMP when repairing drawers! Not nails and screws! And since the drawers were pretty ratty and stained, I gave them a little KSTP treatment! (sorry, no pictures!) They look and smell much better if you will take the time to paint the inside of the drawers of these older pieces!

I think this would make an awesome bedside table or entry piece! Or even a tv cabinet!

I tried to "stage" this little piece with some of my auction finds....

....an old cheese box, some awesome scales and a wood duck decoy. But again, I am not the best photographer and I am definitely more about doing and less "froo-frooing."

I have several dressers and another wash stand to share, so stay tuned!

Info

2 Comments

Simple makeovers for the worst offenders...the KSTP treatment!

There is NO excuse for ugly furniture. With warmer weather just around the corner, it is time to start looking at your furniture with a critical eye and making a list of pieces that CAN be changed with just a little bit of work!

We all have it...those "cheapo" pieces of furniture that are, at the very least, offensive! Maybe they were given to you, maybe you bought them at a "discount" store...maybe you bought it at the thrift store to fill space in a room.

Pressed board construction, laminate tops, dated finishes, pieces you put together with a little allen wrench thingy that came with the worthless little "screws" that promptly strip out and leave the piece wobbly and worthless!

It's ugly and cheap, but seriously who has the money to buy "real wood" furniture when you are struggling from pay check to pay check and having to buy shoes for a kid whose feet seem to grow a size every month.

I get it...I've been there. Fortunately I have learned to shop resale and auctions for "quality" pieces...and even if they need a little TLC, I have the tools, knowledge and time. But not everyone has that...or the money to buy and refinish high quality pieces.

That is why I advocate the KSTP treatment. Let me explain....

First, before you even get to the KSTP treatment, ALWAYS give the piece a good cleaning. On the nastiest, I use ammonia water but some can just be wiped down with a little water and mild detergent. Whatever you need to do to get the gunk off the piece! If it is "stuck" on just scrape it off with a razor! No matter if you scratch the finish...you are going to paint it!

Second, make any and all repairs that need to be made...and if you don't know how to repair it properly, google it!

Okay, now the KSTP treatment....

K- Kilz (my favorite primer but any QUALITY PRIMER will do! That is why this is the KSTP treatment and not the PSTP treatment!)

For smaller pieces I use a spray can only because it is easy and gives me a nice smooth finish. On larger pieces I use a brush and 4" foam roller! TIP! Always shake the can longer than the directions recommend. Kilz will spray on with a "grainy texture" if you don't shake the can well! No biggy since you are going to sand anyway, but just makes it a little easier! Also, pay attention to the temperature recommendations...it matters!

Many paints SAY they are a "primer and paint in one." Sorry, I am old school....I ALWAYS prime and I personally recommend it. If you want a superior finish that will hold up to use and abuse, prime!

S-Sand. A 220 grit paper will usually smooth out the piece after it is primed. I wrap a piece around a sanding sponge block!

If you have "ornate" legs or detailing, use 000-0000 steel wool.

USE YOUR HANDS, not your eyes. Feel the piece.

Trust me, if it isn't smooth, it WILL show after you paint it! Sand it until it is smooth to the touch! If you cleaned the piece well, scraped off all the gunk, this step really should only take a few minutes.

T- Tack cloth. A MUST after you sand but before you paint (or apply any finish). Blow or brush off as much as you can, then use a tack cloth!

You can purchase it at your favorite home improvement store...usually in packages of 2 and relatively inexpensive (around $2)! You can wipe a piece down all day with a clean cloth, but you WILL leave "stuff" on the piece if you don't tack cloth it. Tack cloth will remove EVERYTHING. If you still feel "stuff," hit it with the sand paper again and then tack cloth again!

P-Paint. This is where people usually freak out. My favorite for wood or laminate furniture is oil-based but it can be a tricky paint to work with for a novice and difficult to clean up. Fortunately latex paints have come a long way and are much more durable these days! QUALITY spray paint is probably your best bet for smaller pieces. I say quality because you can buy spray paint a tad cheaper at discount stores, but I am not a huge fan of cheap paint for ANY project! I usually buy Valspar or Rust-oleum from Lowe's.

On smaller pieces of furniture the difference will only be a few dollars but will be worth it in the long run.

Each of the brands come in LOTS of great colors...just find the color you love! I have found very little difference between the two brands...the Valspar tends to dry a tad quicker....but both are quality paints! ALWAYS shake the cans well and follow the directions on the can!!!

I have followed every tip in the book to get rid of the occasional "striping" on large, flat surfaces...like dresser tops or table tops. It doesn't seem to matter how I spray, what the temperature is or how hard the wind is blowing...sometimes I get stripes.

My solution has been to purchase the little "sample pots" of paint custom mixed to match the spray paint I am using and roll it on the large flat surfaces with a 4" foam roller!

Penetrol and Floetrol are a MUST any time you roll or brush on paint...oil or latex!

Use it. It will eliminate the brush and roller marks and give you a MUCH smoother finish!

These are just a VERY few projects using the KSTP treatment (I have done hundreds!)....world of difference for a little bit of work! I am working on a piece right now that is in the S stage...primed and sanded but now I need to figure out what color I want to paint it...soon!

Even light fixtures and paddle fans can be spray painted!!! On metal pieces and furniture hardware, I use metal primer primarily for the "rust retardant" factor!

One last important TIP when using ANY technique to paint anything....ALWAYS give the piece time to cure before you put it to work!

I was always skeptical of those "two day" makeovers they did on tv where they would paint something and then "stage" the pieces with all kinds of stuff within hours of putting a final coat on. (Kind of like getting your nails painted at the salon...even though you dry them for 10 minutes, you are still going to ding them if you dig in your purse for your keys! Unless you get gel polish...awesome stuff!) Trust me, that is the fasted way to ruin a finish! Don't do it...be patient and give the paint time to harden (cure) before you set a lamp on it or try to hang the fixture (trust me...I have had to repaint many pieces because of impatience!)

One dated, nasty, cheapo piece of furniture can ruin an entire room. Toss it or paint it! YOU CAN DO IT!

*I have not been compensated for pimping these products! These are the products I use and work for me!!!*