MORE makeovers...

Surprisingly I have MORE makeovers to share. The weather has been fairly cold and dreary but we have had enough warm days here and there to get a little work done. I get kind of lazy during the winter months…when it is cold and dreary I like to curl up and read. When it is warmer, I NEED to be out working…either at the apartments or on projects.

This first dresser makeover is something you could pretty much do inside on a cold day.

The only thing I had to take it outside to do was distress and seal. But honestly you could do both inside.

I use latex paint for my chalk paint recipe (5 tbs. of Plaster of Paris, 3 tbs. of water, mixed well, then add 2 cups of flat latex paint) and that can used inside.

To do a “wet sand” you would use a sponge with a scrubby on one side…something like this…

After the second coat of chalk paint, before it has thoroughly dried, you would take your sponge, wet it (DAMP NOT DRIPPING!) and start “scrubbing” the areas you want to distress…kind of like dry sand distressing. Keep a bucket of water on hand to rinse the sponge periodically. Doing it like that cuts down on the “dust” created when you dry sand, so you can do it inside.

Then I just seal the entire piece by brushing on a polycrylic (or wax if that is your preference.)

Rather than spend the money on all new hardware, I painted the existing hardware. I use a spray primer and spray paint so that needs to be done outside…but truthfully, you could live with the existing hardware until warmer weather…or just replace it.

But all in all, you COULD do this entire project inside…and it is well worth the time when you consider how much better it looks!

This next piece pretty much had to be done outside on warmer days…I wanted a high gloss lacquer finish on the cabinet and that entails spraying. And I wanted to strip the old finish on the drawer fronts and that definitely has to be done outside.!

I removed and labeled each drawer…that is a MUST because the drawers need to go back into their original position…just mark the underside with a pencil.

I removed the old finish on the drawer fronts using THIS process! I know I refer back to this tutorial a lot, but it is the BEST way to remove old finish or paint…it works and on projects like this, it probably only took me about 30 minutes to remove the old finish on these drawer fronts. Once the old finish was removed, I applied three coats of tung oil finish, rubbing with 0000 steel wool and tack cloth between each coat.

I sprayed the “cabinet” with Kilz, sanded and wiped with tack cloth, and then sprayed 3 LIGHT coats of white lacquer (KTSP).

As you can see from the “before” picture, it did not have legs…but it would have originally and there was even places on the underside to screw in the legs. I ordered new legs HERE and stained them to match the oiled drawer fronts.

Each is completely different and each required a different technique…but both were relatively simple and make a huge impact.

AGAIN, I am sharing how easy it is to do this because AGAIN…

LIFE IS TOO SHORT TO LIVE WITH UGLY FURNITURE!

Info

Comment

Just ANOTHER makeover!!!

A few weeks ago I promised to share some of these makeovers….

I shared the details of this one….

…here….

It sold in a couple of days!

This chest was a mess…

It is solid wood and pretty sturdy. A few of the drawer tracks needed some minor repairs but all in all it was a decent piece…just super ick.

Again, I have to have my “wood fix.” Since the drawer fronts were solid wood, I decided to use gel stain on them.

First I removed all the old hardware and gave the entire piece a good cleaning with a mild detergent.

There is no need to remove the old finish when using gel stain…maybe a light sanding to remove any boogers and dull the shine on the existing finish.

I ONLY use General Finishes brand gel stain. I applied three LIGHT coats with an athletic sock over a rubber glove, allowing each coat to dry overnight. The first coat will look like crud, the second will look a tad better, the third coat looks awesome. I sprayed on polycrylic to seal them. General Finishes has a wipe-on poly and it is pretty awesome…but I had polycrylic on hand so that is what I used.

I sprayed the “cabinet” with Kilz, sand, tack and latex paint (KSTP). I ALWAYS use an additive with paints I am going to roll and brush…Flotroel for latex.

New hardware…and PRESTO….

Another piece saved from the clutches of ugly and dated!
I share these makeovers to remind you….IT’S NOT HARD to take dated, ugly furniture and turn it into something you will be proud to have in your home.

Life is too short to live with ugly furniture!

Info

Comment

Pretty in Pink...

If you “came of age” in the 80’s chances are you saw a John Hughes film. If you haven’t, you are missing out! “Pretty in Pink” was one of my favorites! Check them out…you won’t be disappointed and I can’t think of one that isn’t “kid friendly.”

Which brings me to pink…a color I have always loved but have never really used in my home decor. I must have gotten a “pink bug” because all of a sudden I can’t seem to get enough of it….and since next week is Valentine’s Day, this is a great time to infuse a little pink into my home decor under the guise of “decorating for the holiday.”

I found this little bench in 410 Vintage…the tag said it is walnut but I really think it is mahogany. I used this process to refinish the frame and recovered the seat with the same pink velvet I used for the club chair pillow (makeover here).

Several years ago I refinished a little piano bench to set by the closet so I would have a place to sit and put my shoes on.

In one of my “purging” marathons I moved it out but in all honesty I kinda missed it…so this little bench is a perfect little replacement!

I love my office…a simple room that is really multi purpose…a “thoroughfare” from the living spaces to the master bedroom, a “dressing room,” and of course, an office.

I featured the desk here.

I have seen a few desks over the years that peaked my interest but I still love this desk…it is perfect! Prime example of “buy what you TRULY LOVE and you will never tire of it!”

My office chair looks a lot like a Marcel Gascoin C-chair….I can’t find a picture of this exact chair so I don’t know for certain! Again, I don’t buy pieces like this for their potential value…but because I LOVE them.

I bought it years ago and share it’s little makeover here. Again, still love it!

I have replaced the dresser several times over the years but I LOVE this one! Shared the makeover here and while I loved the dresser that was here before, this one is MORE better!

The little bookcase…just adorbs!

I digress…off to the living room … I found the cutest pink pillows…

…and a yummy smelling pink candle!

The little white pillow was kind of plain so I decided to add some cute pink pom-poms I made out of “furry” yarn. I just tacked them on so they can easily be taken off when I tire of the pink.

The pink pillows will go well with the little bit of Easter decorating I do!

While digging around TJMaxx for pink pillows and candles I found a few other things I thought would be fun for the holiday….cute hedgehog mugs and fun little Valentine’s hand towels!

You don’t have to (or need to) spend a lot of money dressing your home for Valentine’s Day…but it is fun to infuse a little fun and color into an otherwise “drab” time of year!

Funny…I was wearing my pink tennis shoes and a pink vest when I was buying all this pink stuff…the check out lady remarked that I sure must like my pink…lol!

Turns out, I really do! It is so dreary and “wintery” outside and the pink just seems to brighten things up a bit!

I have some leftover pink velvet from the bench makeover…just enough for a few more pink pillows! Now if I can just being myself to sew them…eck!

Info

Comment

Another antique chest makeover...

I promised last week to share all the dresser and chest of drawer makeovers I have been working on. This time of the year it is tough to get a lot of work done over several days because of the temperatures…fortunately this dresser was one I could work on inside.

Takes a little “strategizing” to figure out what I need to do outside on warm days and what can be done inside on cold days.

I knew I was going to paint the cabinet so I managed to get it (and a few others) Kilzed on a warm day. I try to avoid using Kilz inside because it is SUPER stinky…and I like to use the spray kilz on smaller pieces and that can’t be done inside. Sanding and wiping with tack cloth can be done when it is a tad colder so no biggy. I had to strip the drawers and top outside, but that can be done in the cold as well. I was able to bring everything inside to oil the drawers and top and paint the cabinet!

Again, this one didn’t need any major repairs…the only real boo-boo was one missing handle. This hardware was one of the most unique I had ever seen….not only the style but the fact that it was installed “vertically” vs. “horizontally.” Different…I like…so I was determined to use as much of the original hardware as I could.

I removed all the hardware. First I primed them with “metal primer” then I sprayed them with black lacquer.

Since one of the handles was missing and I knew there was NO way I was going to find a replacement, I decided to remove the handles on the top two drawers and replace them with knobs.

That meant the holes in the top drawers had to be puttied…and there is no good way to “disguise” putty holes without painting…but the wood on these drawer fronts was so pretty I really didn’t want to paint them!

The drawer on the right has been stripped…the drawer on the left has not. I just love how “clear and clean” the wood looks after removing the old finish (I used THIS process! Super easy!)

I decided the best way to disguise the puttied holes was to paint a stripe down the drawer fronts. I did this BEFORE applying the tung oil finish.

The stripe needed to be pristine…absolutely NO bleed through…and we all know how tough that is! I read a few tutorials on preventing that…some suggested using modge-podge…one suggested using caulk. I went with the caulk suggestion and it worked like a charm.

I used blue painter’s tape to tape off my stripes, then I ran clear LATEX (NOT silicone) caulk along the edges of the tape….

Then I used my finger to “mash” the caulk along the edge of the tape and wipe off any excess. WORKED LIKE A CHARM! Zero bleed through! I used clear caulk so any caulk that bleed through didn’t show!

I painted the stripes and cabinet. I used a grey latex I had on hand. I added Floetrol…ALWAYS add a paint additive…Penetrol for oil based paints, Floetrol for latex. I use a 4”foam roller and a high quality brush to minimize brush strokes and roller marks. And again, always apply 2-3 LIGHT coats to avoid drips and runs. I oiled the drawer fronts and top with 3 coats of tung oil finish (sand and tack between coats), drilled new holes for the knobs and reattached all the hardware and PRESTO!

Cute as a bug’s ear and super simple!

I just love bringing these pieces back to life!!!!

Info

Comment

Antique dresser makeover....

It’s no secret that this antique dresser is really not “my style.” But I knew it could be beautiful with just a little work…

Okay, so it needed A LOT of work!

One of the first things I do when I buy an old piece like this is really examine it and figure out what, if anything, needs repairs and what is “salvageable.”

It would have been super easy to just slather the whole thing in paint, but I love the combination of paint and wood tones…and if I can salvage any of the wood by refinishing rather painting, I’m going to.

The drawers were in excellent condition…they were intact and they did not “stick.” The only real issue was the missing veneer on the front of the cabinet….a little wood filler and sanding fixed it right up.

The top was in relatively good condition…it did have a few “blemishes.” I have “fixed” blemishes using oxalic acid and it works wonders on solid wood surfaces. But this top is a wood veneer and I haven’t had as much luck on veneers…so I just “embraced” the blemishes and let it be what it is…an old piece with a history.

The drawer fronts were in mint condition…just super yucky. The top and drawer fronts were easily stripped using the 1/2 acetone and 1/2 lacquer thinner mixture. I scrubbed them with #2 steel wool and the mixture, wiping with old rags from time to time. After all the old finish was removed, I “washed” them with mineral spirits and applied three coats of tung oil finish, rubbing with 0000 steel wool and tack cloth between each coat. No stain, just a clear finish!

Rather than refinish the “cabinet” I chalk painted it with homemade chalk paint. My recipe for chalk paint is 5 tablespoons of Plaster of Paris and 3 tablespoons of water, mixed well. Then I add 2 cups of flat paint. I painted two coats and distressed, then sealed it with polyurethane. Again, I do not wax over chalk paint…I just don’t think it is a durable finish.

I was SUPER pumped that ALL the original hardware was there…even the top drawer knobs. They had been replaced but the original knobs were in the drawers…major score! They are just so unique and authentic!

Often the stain is mixed into whatever finish is applied. They did this to make the piece look “uniform.” When you strip the original finish, there is a good chance you are going to strip the original stain color…you WILL see the wood grain and there is a good chance the “color” of the piece will be different. For example, the drawer fronts on this piece were a different tone than the top when all the old finish was stripped away…personally I LOVE this look! But if you want that “uniform” look you need to be prepared to stain the piece…and since different woods stain differently, I would suggest using a gel stain application…that is the only way to ensure a “uniform” look. Or in this case, you could paint the top and only leave the drawers original. To each his own!

This is just one of many I shared on Instagram…and there are even more that aren’t pictured here. Over the next few weeks I will share how each dresser’s makeover!

Each one required a different process to bring it back to life!

Stay tuned!

Info

2 Comments

Building a cat shelter and a new dresser....

I don’t normally share “life hacks” but I just have to share this Kitty shelter. I hope the video tutorial stays up but just in case it doesn’t….basically you take a large storage tub, put a styrofoam cooler inside it…cut a little opening in the tub and cooler…”insulate” around the cooler with blankets (or insulation if you have it) and put a warm blanket in the cooler.

If you have followed along you know I am somewhat of a “cat person.” I have two indoor cats, Litty and Mr. Jinx, one indoor/outdoor cat, Ms. Kitty and then there is Finley. I truly believe Finley is autistic. He isn’t “mentally challenged” he just has “severe social anxiety.” He is terrified of everyone but me and now he will barely come to me. Occasionally I can entice him with food and get him close enough to snatch him up, but he pretty much avoids ALL human contact.

I have had him for 8 years. Before Cleo, he would come in the house but only appear after I was snuggled in bed…then he would get in bed with me. But when Cleo started sleeping with us, he went outside and will not come in the house. Last year when we had a week long deep freeze, I managed to grab him one day only because he was dang near frozen. I brought him in the house to warm him up but he was obviously terrified and spent the entire time hiding…as soon as he could bolt outside he was gone…and there he remains to this day.

Needless to say I worry about him constantly. I have no doubt he has found a cozy spot under the storage building to avoid the elements but I still worry.

When I saw this kitty shelter I immediately bought the stuff to make one for him.

It took a few day, but he eventually moved in and seems quite content in his new warm bed! I placed it in a spot I believe is sheltered from the cold wind and next to the dryer vent so the warm air can blow on it.

I insulated mine with actual insulation because that’s what I had on hand. I put my snuggie in for his bedding…I don’t wash it so it will retain it’s “smell.”

IF you can entice your kitty to come in the house when it is super cold, that is always best. If not, this is a perfect “hack” for an outdoor kitty or stray kitties.

MORE DRESSER MAKEOVERS….

I spent most of last week working on a few dressers. I have finished those up but now I have another batch to start on. It is super tough to find good days to paint outside during the winter months. Dang, I need a heated shop!

This was a teaser I posted on Instagram…

They all turned out super cute but each got a different treatment. So over the next few weeks I will share each one and explain what I had to do to each to bring them back to life!

In the meantime I want to share one that has been lurking in my garage since summer.

When I bought it, it was a nasty mess….

Someone had “stained” it and changed out the hardware. Eck! I think I remember that it had a few wonky drawers. No biggy but AGAIN, make sure you make any repairs BEFORE you make it pretty!

I removed all the hardware and gave it the old KSTP treatment (Kilz, sand, tack, paint)

New hardware….

Again, I’m stuck on white…blah. This weekend we took four dressers into 410 Vintage and ALL of them were white! B.O.R.I.N.G.

I have vowed to use a little color on the dressers I am working on right now!

Stay tuned!

Info

Comment

My "SmileDirectClub" journey...

These are my precious baby girls Christmas morning! I am posting this picture first because some sites automatically snag the first picture in a post…you will see in a minute why I DO NOT want the photos with this post to pop up!

Sooooo….I hesitate to even share this journey for several reasons.

First, I really dislike “endorsing” any product. Not all products work well for everyone. The ortho aligners from SmileDirectClub have both glowing and horrendous reviews. Fortunately for me, my review would be glowing. But obviously that is not the case for everyone and I would hate to recommend this process and someone have a bad outcome. So I am NOT endorsing…I am just sharing MY experience and thoughts on the process! As always, do your own research and do what is best for YOU!

Second, the before and after photos are super nasty! There is NO camera setting or froo-froo staging that is gonna make a close up of 54 year old teeth pretty. I am going to share the photos I had to take of my teeth “before” and then the “after”….and let me tell ya they are NOT pretty! But they do show the progress I made with this system.

(Told you they were nasty!)

All four of my kids needed braces. Since there is 16 years between the oldest and youngest, I think I figured one time that I paid monthly for orthodontic care for almost 20 years. TWENTY YEARS!!! And over $22,000 when you figure they averaged about $5500 a piece.

After my youngest finished her set, I talked to our orthodontist about getting braces myself…my teeth weren’t horrible, but the front top and bottom teeth were kind of crocked and it seems the older I get, the worse they get. At the time he suggested using Invisalign and the cost would be around $5000.

One thing about me I probably should share…I am not a vain person. I have no problem going out in public without makeup. While I use to color my hair and get a mani/pedi regularly, these days my roots could serve as a landing strip and right this minute my two big toenails are the only ones that have a smidge of summer pedi polish left. As far as clothes and shoes…lets just say I still have (and wear) sweatshirts and shoes from 15+ years ago.

I care about my appearance…when necessary, I can dress with the best. I bathe and groom regularly. I do try to make an effort to get my hair done just in case I need to do something other than throw it in a pony tail!

I’m just not going to spend good money on something that just really isn’t necessary. Spending $5000 to straighten a few kinda/sorta/just-a-tad crooked teeth just seemed kinda silly.

But in all honesty, the top front teeth were getting crookeder by the year and their protrusion was really beginning to bug me. My front bottom teeth have always been a little wonky and I just lived with it.

After losing my first 25 pounds (STILL working on that last ten), I was feeling pretty good about myself. I had to buy new bras (20 of the 25 seemed to come out of my boobs). I had to buy new jeans and tops. Brian and I bought bikes and began riding regularly.

So I was feeling pretty sassy…but I really hated my snaggle tooth smile.

That’s when I stumbled across SmileDirectClub…an invisible aligner system that cost WAY less than traditional braces or Invisalign. Rather than go into all the specifics about the product and process, I have provided a link to their site. Again, not endorsing, just sharing.

My process has taken 5 months…I started in August and finished the aligners and started wearing my retainer this week…I will wear the retainer day and night for two weeks and then only at night. I am a HORRIBLE tooth grinder and I think wearing the aligners and retainer at night has actually helped.

I still have two wonky bottom teeth…both have been “wonky” my whole life so I suspect they are tough nuts to move. I have submitted pictures and SmileDirect has agreed to continue the alignment process for the bottom teeth. They guarantee to continue to work with you (at no charge) if you aren’t satisfied. Truthfully I am THRILLED with the outcome, but if I am going to go through this process I might as well take advantage of their guarantee and get those two teeth lined up properly!

So what is my take-away for this process…

1) Be realistic about your teeth. If you have super whacked out teeth or a “bad bite”, I suggest consulting with an orthodontist. My molars were fine and my bite was fine…I just needed to straighten/align- my front teeth…pretty much the top and lower front 8. Remember, an orthodontist is not going to like these things because they take away their business. SmileDirect is going to tell you they can fix your smile because they want your business. So be realistic…do you have a “bite issue”…are your teeth SUPER crooked and/or rotated? If so, I would suggest going the traditional route with an orthodontist. This system is designed for “mild to moderate alignment.”

2) Have good dental health! Teeth, gums, bone structure. I am vigilant about going to the dentist every six months for cleanings and checkups. I get x-rays every year. I brush my teeth 3 times a day and floss every day. I would never recommend this process for someone who isn’t vigilant about their oral health. One of the biggest concerns about these systems that are not monitored by an orthodontist on a regular basis is the potential for bone and gum issues. I review my bone/gum/teeth health every six months with my dentist so I felt confident that I wouldn’t have issues…and I had a scheduled appointment with her during this process and we looked closely at the process together.

Before you start any orthodontic system (supervised or otherwise) make sure you have ALL recommended dental work done…removal of wisdom teeth, any needed crowns or fillings….anything your dentist has suggested, make sure you have it taken care of before you start any ortho work!

3) If you aren’t a discipline person, do not go this route. Having to wear an aligner 22 hours a day is a booger. You can NOT drink anything but water while the aligners are in. Fortunately not a problem for me. But if you are the kind of person who has a coke or tea in your hand all day, you will have a problem! Also, you MUST brush your teeth after you eat or drink anything…so if you snack throughout the day or have a problem with brushing your teeth in a restaurant bathroom, you are going to have issues.

I’ll be honest…taking these things out of your mouth is like taking off your bra after a long day!!!! You know that feeling girls! And it is tempting to want to leave them out and just let your teeth breath!

YOU CAN NOT!!! You have to wear them 22 hours a day for them to affectively work. For me, seeing the weekly progress was all I needed to keep me in line…but trust me when I say there were times when wearing them was just a royal PITA!

4) They may aid in a weight loss journey. Now, I can honestly say that has not been the case for me…I lost my first 25 lbs by August, and since I haven’t really been vigilant the last 4 months, I haven’t lost that last 8-10 lbs….and wearing these didn’t keep me from eating a few cookies after dinner or bacon with my eggs! And of course they have NO bearing on portion control.

But it is a pain to have to take out your aligners and then brush your teeth for a hand full of chips. And again, you won’t be sucking on a big gulp of coke or a Yeti full of sweet tea all day.

For me, seeing the change in my smile had a big impact on my overall self-confidence. That in turn could lead to wanting to eat healthier.

5) No pain, no gain. So if you are a big baby and can’t handle a little discomfort, don’t bother! There was some discomfort and tenderness in my teeth for the first few days after changing the aligners each week. Also, I learned to properly prep my aligners before I ever put them in by using a finger nail file and buffer to file and buff the edges of the aligners to avoid sore or raw spots inside my mouth. I did this EVERY time just to avoid any problems.

I also put new aligners in at night…they tend to be super tight when you first put them in and somewhat uncomfortable…sleeping through the first 8 hours of that was kinda nice.

I also learned to embrace the discomfort and tenderness in my teeth…that meant the aligners where moving those crooked little suckers and progress was being made!!!

SmileDirectClub has a referral system… feel free to use this referral link if you decide to go this route. I think you get some kind of discount and I get a “referral fee.” WIN-WIN!!!

Again, and I can not stress this enough, do your own research!! This has been a positive experience for me, but I can see where some might not benefit from or be successful with this system.

As always, you do what works best for you!

Info

Comment

Styling a master bedroom....

It is no secret I have struggled to “restyle” my master bedroom for years. Truth is, it’s not that I struggled to “restyle” it…I struggled to give it any style at all!.

If you follow the links you can see the transformation over the years!

It started with my grotesquely expensive, heavy, dark and somewhat dated bedroom furniture I bought in 2001!

I don’t know why it took me so long to FINALLY paint it, but when I did it made a huge difference!

The next big change was the flooring…we finally installed hand scraped laminate flooring in both the bedroom and adjoining office.

I love this flooring but after living with it for a few years I will make one observation…avoid dark flooring if at all possible. It is beautiful but shows EVERYTHING…not a good thing if you have a big yellow dog who sheds…or kids with dirty feet! But this was the last room with carpet and I can not tell you how happy I am to have NO carpet in this house!

Next up, changing out the chairs.

LOVE them! But they were a bit on the “grey” side and the walls were more on the “cream” side…so….

Paint…finally got around to doing that.

At one point I even changed out the bed frame….

It had a “distressed” treatment and if you know me that is NOT my thing…but I kinda liked the look for a time.

All of the color choices stemmed from the one color inspiration I found on Pinterest….

It originated on designseeds.com. This site is a source of endless inspiration and in my opinion it is one of the first sites you should visit when designing a room. If you have an element you HAVE to decorate around it will help you find colors that will enhance and even mask it....like that ugly brown couch or the wing back chair your mom gave you.

You can see as I moved forward with each new element, I managed to work in these colors…on the walls, rugs, pillows, chairs, etc.

Eventually we transitioned to a king size mattress…so the queen bed frame no longer worked. I searched high and low for one I would love and finally settled on a simple frame.

I have said time and again…go “neutral” with the big ticket items. Use pillows, throws, rugs, art, and accent furniture to make your “design statement.”

On one of my Pinterest email feeds there was a link to the “Top 10 Fixer Upper Bedrooms.” The bedrooms featured are all “Fixer Upper” bedrooms. I love to look at sites like this because they give me inspiration.

This bed is very similar to mine yet the whole room looks SO much more cozy and inviting.

So why doesn’t my space look as cozy and inviting as this space?

I bet you look at blogs and Pinterest and see all the amazingly styled and perfect spaces…bedrooms, mud rooms, laundry rooms, kitchens…and you just know yours could never be as glam because, well, you live in your house…and so do your kids and animals and spouse…and there is NO WAY you could keep your space looking as dreamy and beautiful.

All the beds on Pinterest and on the blogs are beautifully staged and styled with the pillows, throws and blankets. Like no one every sleeps on it…no baby pees on it…no dog sheds on it…

I GET IT!!!

My room isn’t staged for photos…it is “real life.”

I have a real mental block when it comes to wall decor in my room. Seriously…if you followed the links and looked at the dates you may notice I have been trying to style this room for almost 5 years. To date, I have hung one round mirror…

a canvas…

and two other mirrors….

I absolutely LOVE the 4 prints above the bed in the inspiration photo.

It has only taken me 18 years to find 3 square matted frames I like.

I did not like the artwork in the frames but I love the frames and the “3-D” matting. My original plan was to replace the prints with something “light and airy.” Maybe botanicals or black and whites. But I decided to pick out a few photos from our trips to Colorado…photos that have meaning….places we love!

If you have been around long enough you know I make my bed every day. I firmly believe that making your bed sets a positive tone for the rest of your day (and there is the whole “I might die and people will think I am a bum if my bed is unmade!” thing.) Since I might not be inclined to make my bed every day if it takes more than 60 seconds, I keep my bedding super simple…no froo-froo! Sheet, comforter, top quilt, throw for the animals (who never sleep on it) The dogs and cats sleep on the bed and pillows and yes, they all shed. So I need bleachable and washable bedding. I sleep with 4 pillows so there really is no time or room for fancy designer pillows and shams.

I brought my throw pillows down from the guest room and “staged” the bed…it looks AWESOME…but again, not happening…just too much froo-froo!

I really thought the guest room throw pillows would be the wrong color…but I like them and it has convinced me that I may have too much of the “frosted berry” in the room. I was going for a “pop” of color, but honestly, I think there is too much “pop.”

I really need new lamps…mine are Hobby Lobby lamps from 18 years ago that got a little paint treatment years ago. I couldn’t find lamps I love but I did find lamp shades I like better…unfortunately they aren’t “tall” enough…back they go!

I think big area rugs under the bed make a huge statement…I don’t have that. I went with two scatter rugs on each side of the bed. I did that primarily because this room has two distinct areas…the sitting space and the bed space. I threw down the rug Brian had in his living room and it works pretty well in the “sitting” space. I think maybe if I want to “cozy” up the entire space and make if feel a tad more cohesive I could use two identical rugs in the spaces. But again, serious mental block on what to use so I just live with what I have.

But again, the scatter rugs are the “frosted berry” color and now I’m kinda not liking that…that may be something I change in short order!

The paddle fans were pretty awesome (and expensive) when I hung them 18 years ago. Now they are kind of “meh.” I love the chandelier style lights in the inspiration room but honestly I HAVE to have a paddle fan above my bed…I just can’t be comfortable with out a little air movement. Since I have recess lighting I could probably change these out to a less “in your face” fan.

Window dressings! One of the things I noticed about all the “inspiration rooms” are the beautiful window dressings. Almost all have beautiful, full curtains. Truth is, I really don’t like curtains. Don’t know why. I only have curtains in the front window because sometimes I need to close them to block out the hot sun…but since I live at the end of a cul-de-sac I really don’t need them for privacy. And truth be told, the ones I have are too short…I believe I mentioned that here and yes, I have managed to ignore them for well over a year.

Truthfully I have been waiting on Candice Olsen or Joanna Gaines to come knocking on my door but since they have not, I guess I will have to keep trudging along in this space.

What is my point to this rambling post?

Life…life happens in our homes and while we would love to live in the “inspiration rooms” on blogs and Pinterest, we live in the “real world.” We have to style our spaces to fit our life styles and needs, in the time and budget we have available. We have to accept the fact that sometimes it can take years (or decades) to make a space feel “cozy and inviting”…and that is okay.

Yes, look to the blogs and Pinterest for inspiration…but don’t get frustrated when your space doesn’t look or feel like the inspiration photo after a weekend of hard work or a few trips to the home interior store.

I have been working on this space for 18 years and I still have a lot I want to do!

How do you eat an elephant…one bite at a time…how do you style a bedroom…one element at a time!

Info

Comment

Painted kitchen cabinets and a new entry...

When Matt bought his house over a year ago I promised to share the projects. One year later, I am finally getting around to keeping that promise!

As I mentioned in earlier posts, Matt first had to find his inspiration and make a plan.

His first major project was the entry makeover. My entry makeover was obviously his inspiration but his entry felt SUPER tiny compared to mine.

These aren’t the best before pictures but you can see there is a header across the top of the opening between the living room and the “entry”…so the space felt really tight and cramped…wood flooring (again, a no-no in an entry IMO)…popcorn ceilings.

The “plan” was to remove the closet and header to open up the space, tile the floor and paint the door. Simple!

Before you remove a closet, make sure you have a plan in place for the things you would otherwise store in that space. In Matt’s case, he’s a single guy with two spare bedrooms and closets, a large master bedroom closet and a nice hall pantry. He had plenty of storage space for coats and such…getting rid of the entry closet was not a big deal.

UNTIIIIIL…you start hacking into walls and removing headers that are framed with aluminum studs instead of wood. Interesting to say the least and somewhat of a challenge for a “traditional” builder such as myself.

Lots of sheetrock repair, black paint on the front door that Matt is not real fond of but is living with for the time being, new trim, new tile, new paint. Eventually I think he will replace the light fixture…but it does the job for now.

Here you can see how the entry opens into the living room…before there was a “header” that dropped down 12” and really closed that space in…removing that header not only opened up the entry but it now matches the opening into the hallway that leads to the bedrooms on the other side of the living room.

Matt built the little bench! I found the beautiful metal mirror on clearance at a home interior store.

The fireplace was pretty “dated”…he painted it last year ….

…and we replaced the dated 8x8 beige tile with the same tile we used in the entry. MUUUUCH better!

The very first thing we did before he moved in was built open shelving in the kitchen. We used the “hidden bracket” method I shared here.

His kitchen cabinets were old, nasty oak and he knew he eventually wanted to paint them…but time and finances dictated he wait…the open shelving was a pretty easy and inexpensive way to give the kitchen a tiny update. Since he had his inspiration and had a plan, he knew what colors he wanted to eventually paint the kitchen cabinets…so he knew what color he wanted to paint the shelving.

We simply removed the cabinet to the right of the sink and installed 3 shelves. The cabinet we removed didn’t go to waste…he hung it in the garage above his work bench!

Painted cabinets…this summer he was finally able to complete this part of the plan.

The kitchen before…

The kitchen after…

He hired the actual “painting” part but he did all the prep work himself. He changed out the hinges from nasty ole’ brass looking things to nice new satin nickel hinges.

He also changed out four upper cabinet doors and put reeded glass in them…

The shelves inside the cabinets were old and “sagging” so we built new shelves since you could see them through the glass.

I would like to think I was the inspiration behind that change since I am a tad partial to reed glass cabinet doors!

One element of his original plan was to change out the tile countertops to a solid surface like quartz or granite. Honestly, once the cabinets were painted neither of us found the tops to be nearly as offensive so that part of the plan got bumped to the bottom of the list. It will happen someday, but it is no longer a top priority!

This kitchen is a relatively small space…kind of a “shotgun” or “galley” kitchen if you will…brightening it up with paint and installing the glass front doors and the open shelving made a HUGE difference!

The next big project on his list is his master bathroom. He wants to remove the tub/shower insert and build a walk in shower similar to mine.

Last week I went to an auction and I was able to purchase enough 12x24 floor tile and subway tile for pennies on the dollar!!! He’s been researching the best way to build a shower pan and of course we are experts at demo! So this little project could commence any day!

In the meantime he is busy being a home owner…mowing and raking the yard, mundane chores and dealing with all the grief after a tree falls on your house during a storm! Yep, it even damaged his brand new storage building he is so proud of!

Such is the life of a home owner!

Next week is Christmas and I may take a few weeks off since the whole family will be here! I hope you and yours have a VERY MERRY CHRISTMAS AND HAPPY NEW YEAR!

Info

Comment

Modifying a Dillingham MCM dresser....

So often I buy mid century pieces fully intending to clean them up and sell them. But then, well, I don’t. Inevitably I fall in love with them or one of my kids does (just search mid century on this site…you will see)

Such was the case with this mid century walnut Dillingham dresser….

It did have a few boo-boos…a broken corner piece I was able to fix with a little wood glue…

A tiny bit of chipped veneer I decided to ignore…

And of course the finish was a little worn and tired looking and needed some freshening. First I tried a little Restor-a-finish….

You can kind of see the difference…the right side has been wiped down with Restor-a-finish.

It helped a tad but in the end I scrubbed it down with mineral spirits and steel wool and applied 2 coats of tung oil finish…brightened it right up and blended all the scratches and wear…after all it is a 50+ year old piece…it’s gonna have a few nicks and dings. But again, nothing terribly glaring.

Even though the issues were relatively minor, I hesitated to sell it. I considered painting the sides to disguise the biggest issue…the broken corner.

Enter my kid! Matt absolutely LOVED it and wanted it for an entertainment cabinet!

The dark walnut matches his vintage Lane tables perfectly and like me he has a real affinity for MCM pieces.

So I went to work modifying it for his needs..specifically he needs a place for his turn table.

(Side note…I get tickled at the newest generation of vinyl lovers. People my age remember how thrilled we were to get away from bulky old record players and vinyl records that scratched and skipped. Cassette tapes and walkmans and boom boxes…life changing! Now the younger generation have circled back around to “vinyl” and think they have discovered the greatest thing since sliced bread…HA!!! See, if you live long enough, it all comes back in style!)

So…how to modify this dresser without changing it too much.

I decided to make the bottom two drawers one deep drawer. That entailed removing the face front of the middle drawer and attaching it to the black face frame and bottom drawer…creating what appeared to be two separate drawers…but is actually just one deep drawer.

Confusing I know…let me see if I can show you what I mean in pictures.

First I had to cut the face frame in half to detach it from the cabinet.

Since it is a laminate material, I knew I needed to tape it first to keep it from “splintering.” ALWAYS tape laminate before you cut it and draw your cut mark on the tape!

I could have used a skill saw with a trim blade to make the cut. But I knew a skill saw wouldn’t work to cut the little shelf inside that separated the two drawer spaces. So, darn, I had to buy a new tool…I hate that when that happens! (NOT!)

I have a small Dremel that has similar functions but this little guy is pretty heavy duty…and it worked like a charm!

Next I used my Kreg jig and glue to attach 1x2 pieces of oak to both edges of the face frame. The drawer fronts and face frame only over lapped by about 1/8”…attaching the oak allowed me to secure the face frame to the drawer fronts with glue and screws.

We used a hole saw to cut a hole in the back of the cabinet to feed electric wires through.

That was pretty much all the modification this dresser needed to turn it into the perfect entertainment cabinet!

In the photos you get a peak of a few of the changes Matt has made to his house since he bought it a year ago…the painted fireplace I shared here and the new tile I haven’t shared yet.

I have promised for A YEAR to share a few of the projects he has completed on his house…he opened up the entry, painted his kitchen cabinets and installed glass cabinet doors, built open shelving in his kitchen and laid new tile in the entry and around the fireplace. He has even built a little storage shed! I am so proud of his “projecting” so while I was there taking pictures of his new entertainment cabinet, I snapped a few of his entry and kitchen and I PROMISE to share those next week.